Determination of optimal parameters in drilling composite materials to minimize the machining temperature using the Taguchi method

被引：0
|
作者：
Lopes, A. C. [1 ]
Fernandes, M. G. A. [2 ]
Ribeiro, J. E. P. C. [3 ]
Fonseca, E. M. M. [3 ]
机构：
[1] Polytech Inst Braganca, Braganca, Portugal
[2] Univ Porto, Fac Engn, INEGI, Porto, Portugal
[3] Polytech Inst Braganca, INEGI, LAETA, Braganca, Portugal
来源：
BIODENTAL ENGINEERING IV | 2018年
关键词：
CUTTING PARAMETERS; OPTIMIZATION;
D O I：
暂无
中图分类号：
R78 [口腔科学];
学科分类号：
1003 ;
摘要：
This work aims to determine the best combination of drilling parameters which results in the smaller temperature during the bone drilling procedure. An experimental procedure was adopted with the acquisition of two biomechanical blocks from Sawbones (composite material) with similar properties to the human bone. The goal of this experiment resulted in a drilling process to assess the generated temperature on the drill bit and simultaneously on the bone material. The Taguchi method is a powerful tool in high quality system design, and proved that can be used as optimization method to determine the best parameters combination to obtain the minimum temperatures in the drilling process.
引用
收藏
页码：135 / 140
页数：6
相关论文
共 50 条
  • [1] Selection of optimal machining conditions for the composite materials by using Taguchi and GONNs
    Erkan, Omer
    Demetgul, Mustafa
    Isik, Birhan
    Tansel, Ibrahim Nur
    [J]. MEASUREMENT, 2014, 48 : 306 - 313
  • [2] Optimization of process parameters in drilling of GFRP composite using Taguchi method
    Vankanti, Vinod Kumar
    Ganta, Venkateswarlu
    [J]. JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2014, 3 (01): : 35 - 41
  • [3] Optimization of Drilling Parameters of Fabricated GFRP Composite using Taguchi Method
    Nanubala, Niranjan
    Yadav, Mahesh J.
    Danduk, Chaitanya
    Subbu, S. Kanmani
    [J]. 2016 INTERNATIONAL CONFERENCE ON ENERGY EFFICIENT TECHNOLOGIES FOR SUSTAINABILITY (ICEETS), 2016, : 881 - 885
  • [4] Selection of optimal process parameters by Taguchi method for Drilling GFRP composites using Abrasive Water jet machining Technique
    Prasad, K. Siva
    Chaitanya, G.
    [J]. MATERIALS TODAY-PROCEEDINGS, 2018, 5 (09) : 19714 - 19722
  • [5] Multi-response optimisation of machining parameters during candlestick drilling composite material using membership function and Taguchi method
    Tsao, Chung Chen
    [J]. INTERNATIONAL JOURNAL OF SURFACE SCIENCE AND ENGINEERING, 2015, 9 (2-3) : 189 - 200
  • [6] Optimization of machining parameters to minimize vibration amplitude while machining Al 6063 using gray-based Taguchi method
    Sivasakthivel, P. S.
    Sudhakaran, R.
    Rajeswari, S.
    [J]. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2013, 227 (12) : 1788 - 1799
  • [7] Optimization of machining parameters for abrasive water jet drilling of carbon fiber-reinforced polymer composite material using Taguchi method
    Karatas, Meltem Altin
    Gokkaya, Hasan
    Nalbant, Muammer
    [J]. AIRCRAFT ENGINEERING AND AEROSPACE TECHNOLOGY, 2020, 92 (02): : 128 - 138
  • [8] Multi response optimization of machining parameters of drilling Al/SiC metal matrix composite using grey relational analysis in the Taguchi method
    Haq, A. Noorul
    Marimuthu, P.
    Jeyapaul, R.
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2008, 37 (3-4): : 250 - 255
  • [9] Multi response optimization of machining parameters of drilling Al/SiC metal matrix composite using grey relational analysis in the Taguchi method
    A. Noorul Haq
    P. Marimuthu
    R. Jeyapaul
    [J]. The International Journal of Advanced Manufacturing Technology, 2008, 37 : 250 - 255
  • [10] Parameters Optimization for Sustainable Machining by using Taguchi Method
    Singh, Karmjit
    Sultan, Ibrahim
    [J]. MATERIALS TODAY-PROCEEDINGS, 2019, 18 : 4217 - 4226
12345