Influence of machining parameters on the white layer formation process and its characteristics in turning of hardened steel

被引:2
|
作者
Mehmedovici, M.
Sarici, E.
Buljubasici, I.
Ekinovic, S.
机构
[1] Univ Zenica, Fac Mech Engn, Zenica 72000, Bosnia & Herceg
[2] Univ Tuzla, Fac Mech Engn, Tuzla, Bosnia & Herceg
关键词
D O I
10.1080/10910340701540013
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
This article contains results of experimental research activities of white layer formation (WLF) and its characteristics during a process of turning hardened steels (THS), which have been carried out in laboratories of DD Cimos TMD Ai Gradacac. WLF Characteristics during the THS process were analyzed from the aspects of influence caused by machining parameters as well as tool flank wear width. Experimental tests of tool wear have been performed. The tool used in experimental tool wear was ceramic cutting insert CNGA 120408T, catalogue mark IN22 Al2O3-TiCN. In accordance with achieved results, value of tool flank wear 220 mu m has been set as the criterion of wear. In accordance with defined wear criterion, determination of Level and type of influence that machining parameters have on WLF and its characteristics were carried out in accordance with planned experimental methodology. Experiments have shown that cutting speed and tool flank wear width (for all other machining conditions unchanged) can be used for control of WLF and its characteristics. Structural changes in surface layer of the working piece, during the cutting process of hardened material, except for the WLF are also presented through a transition zone, e.g., dark layer, which has lower hardness than the initial material. Hard WL can take over a Protection role for a machined surface from abrasive actions, while softened zone (dark layer) can take over a function of WL solder with the initial material. Analysis of achieved results points to a possibility of controlling the WLF and its characteristics, and therefore a possibility of using WL in a positive context. The basis for the above mentioned is the effect of additional plastic deformation of WL (APDWL), which occurs only under certain machining conditions. The effect seen, if follows WLF results in decrease of machined surface roughness compared to its expected value. Accordingly there is a possibility for identification of WL on a machined surface by measuring the roughness parameters without previous metallographic preparation of samples.
引用
收藏
页码:313 / 334
页数:22
相关论文
共 50 条
  • [1] White layer formation mechanism in dry turning hardened steel
    Duan, Chunzheng
    Zhang, Fangyuan
    Sun, Wei
    Xu, Xinxin
    Wang, Minjie
    [J]. JOURNAL OF ADVANCED MECHANICAL DESIGN SYSTEMS AND MANUFACTURING, 2018, 12 (02):
  • [2] Influence of cutting condition on white layer induced by high speed machining of hardened steel
    Zhang Fang-yuan
    Duan Chun-zheng
    Xu Xin-xin
    Wang Min-jie
    [J]. The International Journal of Advanced Manufacturing Technology, 2018, 98 : 77 - 84
  • [3] Influence of cutting condition on white layer induced by high speed machining of hardened steel
    Zhang Fang-yuan
    Duan Chun-zheng
    Xu Xin-xin
    Wang Min-jie
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 98 (1-4): : 77 - 84
  • [4] Effects of Process Parameters on White Layer Formation and Morphology in Hard Turning of AISI52100 Steel
    Zhang, Xiao-Ming
    Chen, Li
    Ding, Han
    [J]. JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2016, 138 (07):
  • [5] Influence of tool characteristics on white layer produced by cutting hardened steel and prediction of white layer thickness
    Li, Li
    Lai, Debin
    Ji, Quanxin
    Huang, Jianyou
    Lin, Yongchuan
    Pan, Mingzhang
    Wei, Jueyu
    He, Shengjian
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2021, 113 (3-4): : 1215 - 1228
  • [6] Influence of tool characteristics on white layer produced by cutting hardened steel and prediction of white layer thickness
    Li Li
    Debin Lai
    Quanxin Ji
    Jianyou Huang
    Yongchuan Lin
    Mingzhang Pan
    Jueyu Wei
    Shengjian He
    [J]. The International Journal of Advanced Manufacturing Technology, 2021, 113 : 1215 - 1228
  • [7] Experimental Investigation of White Layer Formation on Machining Silicon Steel in PMEDM Process
    Muthuramalingam, T.
    Phan, Nguyen Huu
    [J]. SILICON, 2021, 13 (07) : 2257 - 2263
  • [8] Experimental Investigation of White Layer Formation on Machining Silicon Steel in PMEDM Process
    T. Muthuramalingam
    Nguyen Huu Phan
    [J]. Silicon, 2021, 13 : 2257 - 2263
  • [9] Research on vibration characteristics of hardened steel precision machining process
    Chen, Guangjun
    Wang, Yushuo
    Xu, Rui
    Liu, Xianli
    [J]. Key Engineering Materials, 2014, 621 : 63 - 68
  • [10] Some observations of the chip formation process and the white layer formation in high speed milling of hardened steel
    Ekinovic, S
    Dolinsek, S
    Jawahir, IS
    [J]. MACHINING SCIENCE AND TECHNOLOGY, 2004, 8 (02) : 327 - 340