Wear behavior and cutting performance of nanostructured hard coatings on cemented carbide cutting tools in hard milling

被引：68
|
作者：
Caliskan, Halil [1 ]
Kurbanoglu, Cahit [2 ]
Panjan, Peter [3 ]
Cekada, Miha [3 ]
Kramar, Davorin [4 ]
机构：
[1] Bartin Univ, Dept Mech Engn, TR-74100 Bartin, Turkey
[2] Istanbul Medeniyet Univ, Dept Mech Engn, TR-34730 Istanbul, Turkey
[3] Jozef Stefan Inst, Dept Thin Films & Surfaces, Ljubljana 1000, Slovenia
[4] Univ Ljubljana, Fac Mech Engn, Ljubljana 1000, Slovenia
来源：
TRIBOLOGY INTERNATIONAL | 2013年 / 62卷
关键词：
Nanolayer and nanocomposite coating; Tool wear; Carbide cutting tool; Hard milling; NANOCOMPOSITE COATINGS; MECHANICAL-PROPERTIES; OXIDATION BEHAVIOR; CHIP FORMATION; THIN-FILMS; STEEL; PVD; MICROSTRUCTURE; RESISTANCE; LAYER;
D O I：
10.1016/j.triboint.2013.02.035
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
The influence of nanolayer AlTiN/TiN and multilayer nanocomposite TiAlSiN/TiSiN/TiAlN hard coatings on the wear behavior and cutting performance of carbide cutting tools was investigated in face milling of hardened AISI O2 cold work tool steel (similar to 58 HRC) at dry conditions. Characterization of the coatings was performed using nanoindentation, scratch test, reciprocating multi-pass wear test. The chips forming during cutting process were also analyzed. Results showed that abrasive and oxidation wear are dominant tool failures. The nanolayer AlTiN/TiN coating gives the best adhesion to the substrate, the best wear resistance in machining and thus provides the longest lifetime with carbide inserts. (C) 2013 Elsevier Ltd. All rights reserved.
引用
收藏
页码：215 / 222
页数：8
相关论文
共 50 条
  • [1] Wear behavior and cutting performance of CrAlSiN and TiAlSiN hard coatings on cemented carbide cutting tools for Ti alloys
    Chang, Yin-Yu
    Lai, Hsing-Ming
    [J]. SURFACE & COATINGS TECHNOLOGY, 2014, 259 : 152 - 158
  • [2] Investigation of the performance of carbide cutting tools with hard coatings in hard milling based on the response surface methodology
    Caliskan, Halil
    Kurbanoglu, Cahit
    Panjan, Peter
    Kramar, Davorin
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2013, 66 (5-8): : 883 - 893
  • [3] Investigation of the performance of carbide cutting tools with hard coatings in hard milling based on the response surface methodology
    Halil Çalışkan
    Cahit Kurbanoğlu
    Peter Panjan
    Davorin Kramar
    [J]. The International Journal of Advanced Manufacturing Technology, 2013, 66 : 883 - 893
  • [4] Recent developments in the new generation of hard coatings applied on cemented carbide cutting tools
    Derakhshandeh, M. R.
    Eshraghi, M. J.
    Razavi, M.
    [J]. INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2023, 111
  • [5] State of the art in hard coatings for carbide cutting tools
    Prengel, HG
    Pfouts, WR
    Santhanam, AT
    [J]. SURFACE & COATINGS TECHNOLOGY, 1998, 102 (03): : 183 - 190
  • [6] State of the art in hard coatings for carbide cutting tools
    Prengel, H.G.
    Pfouts, W.R.
    Santhanam, A.T.
    [J]. Surface and Coatings Technology, 1998, 102 (03): : 183 - 190
  • [7] Optimization of cutting conditions in hard milling with the performance of cemented carbide tool material considered
    Xiaobin Cui
    Xingshuai Zheng
    Jingxia Guo
    [J]. The International Journal of Advanced Manufacturing Technology, 2018, 96 : 2161 - 2173
  • [8] Optimization of cutting conditions in hard milling with the performance of cemented carbide tool material considered
    Cui, Xiaobin
    Zheng, Xingshuai
    Guo, Jingxia
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 96 (5-8): : 2161 - 2173
  • [9] Hard coatings on cutting tools
    L. A. Ivashchenko
    G. V. Rusakov
    V. I. Ivashchenko
    O. K. Porada
    [J]. Powder Metallurgy and Metal Ceramics, 2004, 43 : 606 - 610
  • [10] Hard coatings on cutting tools
    Ivashchenko, LA
    Rusakov, GV
    Ivashchenko, VI
    Porada, OK
    [J]. POWDER METALLURGY AND METAL CERAMICS, 2004, 43 (11-12) : 606 - 610
12345