Microstructural Control During Spray Deposition Processing of Liquid Immiscible Alloys

被引：0
|
作者：
Anil, M. [1 ]
Ojha, S. N. [1 ]
机构：
[1] Banaras Hindu Univ, Inst Technol, Dept Met Engn, Varanasi 221005, Uttar Pradesh, India
来源：
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS | 2007年 / 60卷 / 2-3期
关键词：
D O I：
暂无
中图分类号：
TF [冶金工业];
学科分类号：
0806 ;
摘要：
Alloys based on Al-Ph and Cu-Pb systems were gas atomized and spray deposited on a copper substrate. Microstructure of spray deposited Cu-20Pb alloy showed an equiaxed grain morphology of the primary a-phase in contrast to cellular-dendritic morphology of a wide size range of powder particles. A uniform distribution of ultrafine Pb particles was observed in the deposit of Al-4Cu-20Pb alloy against a bimodal size distribution of Pb particles in atomised powder particles of this alloy. The wear rate of Cu-20 Pb alloy was observed to be higher than that of Al-4Cu-20Pb alloy at low load and sliding velocity. However, the former indicated a low wear rate in severe wear regime of high load and sliding velocity. The mode of solidification of liquid immiscible alloys is discussed and their wear behaviour analysed in light of solidification structure of alloys generated during spray deposition processing.
引用
收藏
页码：317 / 321
页数：5
相关论文
共 50 条
  • [1] Spray forming and wear characteristics of liquid immiscible alloys
    Gouthama
    Rudrakshi, G. B.
    Ojha, S. N.
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2007, 189 (1-3) : 224 - 230
  • [2] Microstructural control during processing of aluminium canning alloys
    Marshall, G.J.
    Materials Science Forum, 1996, 217-222 (pt 1): : 19 - 30
  • [3] Microstructural control during processing of aluminium canning alloys.
    Marshall, GJ
    ALUMINIUM ALLOYS: THEIR PHYSICAL AND MECHANICAL PROPERTIES, PTS 1-3, 1996, 217 : 19 - 30
  • [4] MICROSTRUCTURAL CONTROL DURING PROCESSING OF CONTINUOUSLY CAST-ALUMINUM ALLOYS
    STRID, J
    FURU, T
    OERSUND, R
    NES, E
    JOURNAL OF METALS, 1988, 40 (07): : A74 - A74
  • [5] LIQUID IMMISCIBLE ALLOYS
    RATKE, L
    DIEFENBACH, S
    MATERIALS SCIENCE & ENGINEERING R-REPORTS, 1995, 15 (7-8): : 263 - 347
  • [6] Microstructural modifications induced during spray deposition of Al-Si-Fe alloys and their mechanical properties
    Srivastava, V. C.
    Mandal, R. K.
    Ojha, S. N.
    Venkateswarlu, K.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 471 (1-2): : 38 - 49
  • [7] Containerless processing of immiscible alloys
    Egry, I
    Herlach, DM
    Ratke, L
    Chatain, D
    FIRST INTERNATIONAL SYMPOSIUM ON MICROGRAVITY RESEARCH & APPLICATIONS IN PHYSICAL SCIENCES AND BIOTECHNOLOGY, VOLS I AND II, PROCEEDINGS, 2001, 454 : 669 - 675
  • [8] Microstructural evolution during the initial stages of spray atomization and deposition
    Xu, Q
    Lavernia, EJ
    SCRIPTA MATERIALIA, 1999, 41 (05) : 535 - 540
  • [9] Directional Solidification and Microstructural Refinement of Immiscible Alloys
    Jie He
    Jiuzhou Zhao
    Haili Li
    Xianfei Zhang
    Qinxia Zhang
    Metallurgical and Materials Transactions A, 2008, 39 : 1174 - 1182
  • [10] Directional solidification and microstructural refinement of immiscible alloys
    He, Jie
    Zhao, Jiuzhou
    Li, Haili
    Zhang, Xianfei
    Zhang, Qinxia
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2008, 39A (05): : 1174 - 1182
12345