Turbine blade boundary layer separation suppression via synthetic jet: An experimental and numerical study

被引：27
|
作者：
Bernardini, C. [1 ]
Carnevale, M. [1 ]
Manna, M. [2 ]
Martelli, F. [1 ]
Simoni, D. [3 ]
Zunino, P.
机构：
[1] Univ Florence, Florence, Italy
[2] Univ Naples Federico II, Naples, Italy
[3] Univ Genoa, Genoa, Italy
来源：
JOURNAL OF THERMAL SCIENCE | 2012年 / 21卷 / 05期
关键词：
Synthetic Jet; Separated Flow; Active Flow Control; Unsteady Flow; Ultra High Lift LPT; ACTIVE FLOW-CONTROL; TRANSITION;
D O I：
10.1007/s11630-012-0561-2
中图分类号：
O414.1 [热力学];
学科分类号：
摘要：
The present paper focuses on the analysis of a synthetic jet device (with a zero net massflow rate) on a separated boundary layer. Separation has been obtained on a flat plate installed within a converging-diverging test section specifically designed to attain a local velocity distribution typical of a high-lift LPT blade. Both experimental and numerical investigations have been carried out. Unsteady RANS results have been compared with experiments in terms of time-averaged velocity and turbulence intensity distributions. Two different Reynolds number cases have been investigated, namely Re = 200, 000 and Re = 70, 000, which characterize low-pressure turbine operating conditions during take-off/landing and cruise. A range of synthetic jet aerodynamic parameters (Strouhal number and blowing ratio) has been tested in order to analyze the features of control - separated boundary layer interaction for the aforementioned Reynolds numbers.
引用
收藏
页码：404 / 412
页数：9
相关论文
共 50 条
  • [1] Turbine Blade Boundary Layer Separation Suppression via Synthetic Jet: an Experimental and Numerical Study
    Bernardini
    Carnevale
    Manna
    Martelli
    Simoni
    Zunino
    Journal of Thermal Science, 2012, 21 (05) : 404 - 412
  • [2] Turbine blade boundary layer separation suppression via synthetic jet: An experimental and numerical study
    C. Bernardini
    M. Carnevale
    M. Manna
    F. Martelli
    D. Simoni
    P. Zunino
    Journal of Thermal Science, 2012, 21 : 404 - 412
  • [3] Boundary Layer Separation from the Trailing Edge of a Turbine Blade
    Simoni, Daniele
    Ubaldi, Marina
    Zunino, Pietro
    FMA'08: PROCEEDINGS OF THE 6TH IASME/WSEAS INTERNATIONAL CONFERENCE ON FLUID MECHANICS AND AERODYNAMICS: NEW ASPECTS OF FLUID MECHANICS AND AERODYNAMICS, 2008, : 252 - 258
  • [4] NUMERICAL SIMULATION OF TURBINE BLADE COOLING VIA JET IMPINGEMENT
    Al Ali, Abdulla R.
    Janajreh, Isam
    CLEAN, EFFICIENT AND AFFORDABLE ENERGY FOR A SUSTAINABLE FUTURE, 2015, 75 : 3220 - 3229
  • [5] Numerical investigation of boundary layer separation control on the low-pressure turbine blade by oscillatory blowing
    Yang, PengCheng
    Chen, ShaoWen
    Chen, ShuaiTong
    Liu, GuanYu
    AEROSPACE SCIENCE AND TECHNOLOGY, 2024, 146
  • [6] An experimental study of boundary layer separation flow control strategy to low pressure turbine blade at steady inflow state
    Sun S.
    Lei Z.-J.
    Li W.
    Dong L.-H.
    Fu Y.
    Zhang Q.
    1600, Journal of Propulsion Technology (37): : 1074 - 1083
  • [7] Unsteady boundary layer development on a wind turbine blade: an experimental study of a surrogate problem
    Daniel R. Cadel
    Di Zhang
    K. Todd Lowe
    Eric G. Paterson
    Experiments in Fluids, 2018, 59
  • [8] Unsteady boundary layer development on a wind turbine blade: an experimental study of a surrogate problem
    Cadel, Daniel R.
    Zhang, Di
    Lowe, K. Todd
    Paterson, Eric G.
    EXPERIMENTS IN FLUIDS, 2018, 59 (04)
  • [9] Influence of synthetic jet location on boundary layer separation control
    Lee, C
    Hong, G
    Mallinson, SG
    DEVICE AND PROCESS TECHNOLOGIES FOR MEMS, MICROELECTRONICS, AND PHOTONICS III, 2004, 5276 : 230 - 239
  • [10] Numerical simulation of the interaction of a circular synthetic jet with a boundary layer
    Zhou, Jue
    Zhong, Shan
    COMPUTERS & FLUIDS, 2009, 38 (02) : 393 - 405
12345