A sensitivity study of size parameters in a twin-type rolling piston compressor

被引：16

作者：

Yang, Jang-Sik ^{[1
]}

Mei, Lu ^{[2
]}

Noh, Ki-Youl ^{[2
]}

Moon, Seok-Hwan ^{[2
]}

Sa, Bum-Dong ^{[3
]}

Choi, Gyung-Min ^{[2
]}

Kim, Duck-Jool ^{[4
]}

机构：

[1] Pusan Natl Univ, Rolls Royce Univ Technol Ctr Thermal Management, Pusan 609735, South Korea

[2] Pusan Natl Univ, Grad Sch Mech Engn, Pusan 609735, South Korea

[3] LG Elect Inc, Energy Components R&D Dept, Seoul 153802, South Korea

[4] Pusan Natl Univ, Res Inst Mech Technol, Pusan 609735, South Korea

来源：

INTERNATIONAL JOURNAL OF REFRIGERATION-REVUE INTERNATIONALE DU FROID | 2013年 / 36卷 / 03期

关键词：

Rolling piston compressor; Dynamic analysis; Sensitivity study; Energy Efficiency Ratio; Optimization;

D O I：

10.1016/j.ijrefrig.2012.08.027

中图分类号：

O414.1 [热力学];

学科分类号：

摘要：

In this paper, numerical studies on size parameters has been conducted to improve the performance of a twin-type rolling piston compressor, which has two cylinders called upper and lower cylinders with phase difference of 180 degrees. In order to verify the computational reliability, the simulated results were compared with experimental ones. Sensitivity analysis of each parameter has been undertaken to investigate the influence of the parameters on compressor performance. Especially, size optimization has been studied to find an optimal combination of size parameters based on the sensitivity analysis of each parameter at the given operational condition and working volume. It was demonstrated that the maximum limits on the valve lift (y(max)) and the suction port diameter (D_sp) showed the highest sensitivity to the compressor performance and optimum design condition, which corresponded to an Energy Efficiency Ratio (EER) that is 2.6% higher compared to the reference condition. Crown Copyright 2012 Published by Elsevier Ltd and IIR. All rights reserved.

引用

页码：786 / 794

页数：9

共 48 条

[1] A STUDY ON SUCTION GAS HEATING IN A ROLLING PISTON TYPE ROTARY-COMPRESSOR
YANAGISAWA, T
SHIMIZU, T
DOHI, M
NIHASHI, S
BULLETIN OF THE JSME-JAPAN SOCIETY OF MECHANICAL ENGINEERS, 1984, 27 (226): : 741 - 748
[2] Numerical Simulation for Flow of Rolling Piston Type of Rotary Compressor
Hsu, Li-Chieh
Wong, Guo-Wei
Lu, Po-Jui
Hsu, Fu-Shun
Chen, Ying-Chien
ENERGIES, 2020, 13 (10)
[3] FOAMING OF REFRIGERATING OIL IN A ROLLING PISTON TYPE ROTARY COMPRESSOR.
Yanagisawa, T.
Shimizu, T.
International Journal of Refrigeration, 1986, 9 (01) : 17 - 20
[4] Ultrasonic measurement of clearances of a rolling-piston type rotary compressor
Kim, N
Kim, J
REVIEW OF PROGRESS IN QUANTITATIVE NONDESTRUCTIVE EVALUATION, VOLS 17A AND 17B, 1998, : 1891 - 1898
[5] LEAKAGE LOSSES WITH A ROLLING PISTON TYPE ROTARY COMPRESSOR. I. RADIAL CLEARANCE ON THE ROLLING PISTON.
Yanagisawa, T.
Shimizu, T.
International Journal of Refrigeration, 1985, 8 (02) : 75 - 84
[6] Optical measurement of discharge valve modal parameters for a rolling piston refrigeration compressor
Prater, G
Hnat, WP
MEASUREMENT, 2003, 33 (01) : 75 - 84
[7] INFLUENCE OF CLEARANCE VOLUME ON THE PERFORMANCE OF THE ROLLING PISTON TYPE ROTARY-COMPRESSOR
YANAGISAWA, T
SHIMIZU, T
BULLETIN OF THE JSME-JAPAN SOCIETY OF MECHANICAL ENGINEERS, 1983, 26 (214): : 537 - 544
[8] LOSS ANALYSIS OF ROLLING-PISTON TYPE SPEED CONTROLLED ROTARY COMPRESSOR.
Iwata, Hiroshi
Sakazume, Akio
Yokoyama, Kenziroh
Nippon Kikai Gakkai Ronbunshu, B Hen/Transactions of the Japan Society of Mechanical Engineers, Part B, 1985, 51 (465): : 1736 - 1741
[9] Investigation on heat exchange and lubrication of rolling piston type rotary compressor in air conditioner
Zhang, HJ
Gao, YX
Feng, QY
Wu, JH
Dong, XJ
Yang, S
CRYOGENICS AND REFRIGERATION - PROCEEDINGS OF ICCR 98, 1998, : 278 - 281
[10] Tribology study of rolling piston compressor using R-407C
Yue, H
Zhao, C
Yang, J
Su, Z
COMPRESSORS AND THEIR SYSTEMS, 2001, 2001 (07): : 459 - 463

← 1 2 3 4 5 →