Crystallographic Analysis of Lath Martensite in Ferrite-Martensite Dual Phase Steel Sheet Annealed after Cold-Rolling

被引：0

作者：

Yoshida, Hiromi ^{[1
]}

Takagi, Shusaku ^{[1
]}

Sakai, Shota ^{[2
]}

Morito, Shigekazu ^{[2
]}

Ohba, Takuya ^{[2
]}

机构：

[1] JFE Steel Corp, Steel Res Lab, Fukuyama, Hiroshima 7218510, Japan

[2] Shimane Univ, Dept Mat Sci, Hamada, Shimane, Japan

来源：

TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN | 2013年 / 99卷 / 10期

关键词：

crystallography; lath martensite; dual phase steel; SEM/EBSD; orientation relationship between ferrite and martensite; LOW-CARBON STEELS; FE-NI ALLOYS; MECHANICAL-PROPERTIES; COOLING RATE; GRAIN-SIZE; MORPHOLOGY; STRENGTH; FRACTION;

D O I：

10.2355/tetsutohagane.99.625

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

Cold-rolled and annealed ferrite-martensite dual phase (DP) steel sheets are a useful material for automotive applications because of their excellent balance of strength and ductility. Although few research papers have examined the crystallography and microstructure of lath martensite in DP steel, the characteristics of lath martensite have been investigated in single-phase martensitic steel. In the present study, the crystallography and microstructure of lath martensite in a ferrite-martensite dual phase were studied using electron microscopy and electron diffraction analysis, and the crystallographic orientation relationship between the ferrite and martensite was analyzed. The main results are as follows: (1) The lath martensite in DP steel consists of some number of packets, and these packets consist of blocks. This structure is the same as the microstructure of single-phase lath martensite. (2) The habit planes of the martensite laths in a packet tend to be parallel to the close-packed plane of the adjacent ferrite grain, whose fraction is about 30%.

引用

页码：33 / 41

页数：9

共 50 条

[1] Crystallographic Analysis of Lath Martensite in Ferrite-Martensite Dual Phase Steel Sheet Annealed after Cold-Rolling
Yoshida, Hiromi
Takagi, Shusaku
Sakai, Shota
Morito, Shigekazu
Ohba, Takuya
[J]. ISIJ INTERNATIONAL, 2015, 55 (10) : 2198 - 2205
[2] Development of a high strength and ductile Nb-bearing dual phase steel by cold-rolling and intercritical annealing of the ferrite-martensite microstructures
Kalashami, Ali Ghatei
Kermanpur, Ahmad
Najafizadeh, Abbas
Mazaheri, Yousef
[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 658 : 355 - 366
[3] Mutual mechanical effects of ferrite and martensite in a low alloy ferrite-martensite dual phase steel
Ebrahimian, A.
Banadkouki, S. S. Ghasemi
[J]. JOURNAL OF ALLOYS AND COMPOUNDS, 2017, 708 : 43 - 54
[4] Ferrite-martensite dual phase anti-erosion steel
Endo, S
Nagae, M
[J]. ISIJ INTERNATIONAL, 1996, 36 (01) : 95 - 100
[5] The effect of martensite volume fraction on the scratch and abrasion resistance of a ferrite-martensite dual phase steel
Xu, Xiaojun
van der Zwaag, Sybrand
Xu, Wei
[J]. WEAR, 2016, 348 : 80 - 88
[6] Ferrite hardening response in a low alloy ferrite-martensite dual phase steel
Fereiduni, E.
Banadkouki, S. S. Ghasemi
[J]. JOURNAL OF ALLOYS AND COMPOUNDS, 2014, 589 : 288 - 294
[7] Microstructure Distribution Parameters for Ferrite-Martensite Dual-Phase Steel
M. Yu
R. B. Gou
W. J. Dan
S. S. Zhang
T. Jiang
S. Chen
C. Lu
J. X. Zhang
[J]. Strength of Materials, 2021, 53 : 173 - 182
[8] LOAD LOSS RESISTANCE OF FERRITE-MARTENSITE DUAL PHASE STEEL SPRING
KANETSUKI, Y
[J]. TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1987, 73 (05): : S451 - S451
[9] Microstructure Distribution Parameters for Ferrite-Martensite Dual-Phase Steel
Yu, M.
Gou, R. B.
Dan, W. J.
Zhang, S. S.
Jiang, T.
Chen, S.
Lu, C.
Zhang, J. X.
[J]. STRENGTH OF MATERIALS, 2021, 53 (01) : 173 - 182
[10] Fine-grained dual-phase steels fabricated via cold-rolling ferrite-martensite structure and subsequent intercritical annealing
Deng, Y. G.
Yang, Y. P.
[J]. JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2023, 27 : 3881 - 3886

← 1 2 3 4 5 →