Research of Submerged Friction Stir Welded AZ31B Magnesium Alloy

被引：0
|
作者：
Wang Kuaishe [1 ]
Zhou Longhai [1 ]
Wu Jialei [1 ]
Wang Wen [1 ]
机构：
[1] Xian Univ Architecture & Technol, Coll Met Engn, Xian 710055, Peoples R China
来源：
RARE METAL MATERIALS AND ENGINEERING | 2012年 / 41卷 / 06期
关键词：
AZ31B magnesium alloy; submerged friction stir welding; microstructure; mechanical properties; TEXTURE; MICROSTRUCTURE;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
AZ31B magnesium alloy was joined by friction stir welding (FSW) and submerged friction stir welding (SFSW), respectively, and the microstructure and mechanical properties of the joints were investigated. The experimental results show that the nugget zone in SFSW joint is characterized by fine and equiaxed recrystallized grains. Increasing of the travel speed will induce an increase in grain size and a decrease in microhardness in the nugget zone. The microstructure of the FSW joint on the surface is coarser and more inhomogeneous than that in the center, while the microstructure of the SFSW joint on the surface is obviously finer than that in the center. The microhardness of the FSW joint on the surface is lower than that in the center, while the SFSW joint has the opposite trend. When the rotation speed is 950 r.min(-1) and the travel speed is 75 mm.min(-1), the maximum ultimate tensile strength of the SFSW joint reaches 72% that of the base material. The fracture surface of the SFSW joints exhibits cleavage-like feature.
引用
收藏
页码：1111 / 1115
页数：5
相关论文
共 14 条
  • [1] Microstructure and tensile properties of friction stir welded AZ31B magnesium alloy
    Afrin, N.
    Chen, D. L.
    Cao, X.
    Jahazi, M.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2008, 472 (1-2): : 179 - 186
  • [2] The weldability of AZ31 magnesium alloy by friction stir welding
    Aydin, M.
    Bulut, R.
    [J]. KOVOVE MATERIALY-METALLIC MATERIALS, 2010, 48 (02): : 97 - 103
  • [3] Tensile properties of a friction stir welded magnesium alloy: Effect of pin tool thread orientation and weld pitch
    Chowdhury, S. M.
    Chen, D. L.
    Bhole, S. D.
    Cao, X.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2010, 527 (21-22): : 6064 - 6075
  • [4] Friction stir welding of AZ31 magnesium alloy rolled sheets: Influence of processing parameters
    Commin, L.
    Dumont, M.
    Masse, J. -E.
    Barrallier, L.
    [J]. ACTA MATERIALIA, 2009, 57 (02) : 326 - 334
  • [5] Dynamic recrystallization in AZ31 magnesium alloy
    Fatemi-Varzaneh, S. M.
    Zarei-Hanzaki, A.
    Beladi, H.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 456 (1-2): : 52 - 57
  • [6] Friction stir welding and processing
    Mishra, RS
    Ma, ZY
    [J]. MATERIALS SCIENCE & ENGINEERING R-REPORTS, 2005, 50 (1-2): : 1 - 78
  • [7] Selection of FSW tool pin profile, shoulder diameter and material for joining AZ31B magnesium alloy - An experimental approach
    Padmanaban, G.
    Balasubramanian, V.
    [J]. MATERIALS & DESIGN, 2009, 30 (07) : 2647 - 2656
  • [8] Pareek M, 2006, TRENDS IN WELDING RESEARCH, PROCEEDINGS, P421
  • [9] Effect of micro-texture on fracture location in friction stir weld of Mg alloy AZ61 during tensile test
    Park, SHC
    Sato, YS
    Kokawa, H
    [J]. SCRIPTA MATERIALIA, 2003, 49 (02) : 161 - 166
  • [10] Basal plane texture and flow pattern in friction stir weld of a magnesium alloy
    Park, SHC
    Sato, YS
    Kokawa, H
    [J]. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2003, 34A (04): : 987 - 994
12