3D circular interpolation motion equivalent to cone-frustum cutting in five-axis machining centers and its sensitivity analysis

被引：10

作者：

Kato, Noriyuki ^{[1
]}

Sato, Ryuta ^{[2
]}

Tsutsumi, Masaomi ^{[1
]}

机构：

[1] Tokyo Univ Agr & Technol, Koganei, Tokyo 1848588, Japan

[2] Kobe Univ, Kobe, Hyogo 6578501, Japan

来源：

FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012 | 2012年 / 1卷

关键词：

Standardization; Measurement; Ball bar; Sensitivity coefficient; COMPENSATION;

D O I：

10.1016/j.procir.2012.04.094

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The present paper describes a testing method for five-axis machining centers using three-dimensional circular interpolation movement equivalent to cone-frustum cutting. In the present paper, the test conditions, such as the half apex angle of cone-frustum and the sensitive directions of the ball bar device were investigated. In addition, the sensitivity coefficient of each axis was investigated. It is found from the analysis of the sensitivity coefficient that the trajectory due to the errors of the axis of rotation is strongly affected by the sensitive direction of the ball bar for the case of a half apex angle of 45 degrees. (C) 2012 The Authors. Published by Elsevier B.V. Selection and/or peer-review under responsibility of Professor Konrad Wegener

引用

页码：530 / 535

页数：6

共 18 条

[1] Sensitivity analysis in ballbar measurement of 3d circular interpolation motion equivalent to cone-frustum cutting in five-axis machining centers
Tokyo University of Agriculture and Technology, Dept. of Mechanical Systems Engineering, 2-24-16, Nakacho, Koganei Tokyo 184-8588, Japan
Nihon Kikai Gakkai Ronbunshu C, 2012, 791 (2677-2688):
[2] Analysis of circular trajectory equivalent to cone-frustum milling in five-axis machining centers using motion simulator
Kato, Noriyuki
Tsutsumi, Masaomi
Sato, Ryuta
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2013, 64 : 1 - 11
[3] Sensitivity Analysis in Ball Bar Measurement of Three-Dimensional Circular Movement Equivalent to Cone-Frustum Cutting in Five-Axis Machining Centers
Kato, Noriyuki
Tsutsumi, Masaomi
Tsuchihashi, Yu
Sato, Ryuta
Ihara, Yukitoshi
JOURNAL OF ADVANCED MECHANICAL DESIGN SYSTEMS AND MANUFACTURING, 2013, 7 (03): : 317 - 332
[4] Analysis of three-dimensional circular motion trajectories of five-axis machining centres simulating cone-frustum cutting
Kato, Noriyuki
Tsutsumi, Masaomi
Tsuchihashi, Yu
Sato, Ryuta
Yumiza, Daisuke
Cui, Chengri
Ihara, Yukitoshi
Nihon Kikai Gakkai Ronbunshu, C Hen/Transactions of the Japan Society of Mechanical Engineers, Part C, 2012, 78 (787): : 964 - 975
[5] ERROR ANALYSIS BY SQUARE 3X3 MACHINING METHOD FOR FIVE-AXIS MACHINING CENTERS
Sakamoto, Shigehiko
Yokoyama, Atsushi
Nakayasu, Kazumasa
Suzuki, Toshihiro
Koike, Shinji
PROCEEDINGS OF THE JSME 2020 CONFERENCE ON LEADING EDGE MANUFACTURING/MATERIALS AND PROCESSING, LEMP2020, 2020,
[6] The Motion Analysis and Its Modeling of Machining the Ruled Curved Surface by Five-axis Linkage WEDM
Wang, Xinrong
Li, Xiaohai
Zhang, Xia
MATERIALS PROCESSING TECHNOLOGIES, PTS 1 AND 2, 2011, 154-155 : 891 - 895
[7] A flexible five-axis trochoidal milling method for machining complex 3D slots
Zhang, Zhengzhong
Cai, Yonglin
Wang, Haitong
Zhao, Mingbo
Mei, Jiawei
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2024, 134 (9-10): : 4609 - 4624
[8] A combined 3D linear and circular interpolation technique for multi-axis CNC machining
Liang, H
Hong, H
Svoboda, J
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2002, 124 (02): : 305 - 312
[9] Avoiding feed fluctuation for five-axis interpolation using 3D clothoid and B-spline
Zheng Sun
Liyong Niu
Bin Liu
Kedian Wang
Bo Li
Xuesong Mei
The International Journal of Advanced Manufacturing Technology, 2022, 121 : 2747 - 2757
[10] Avoiding feed fluctuation for five-axis interpolation using 3D clothoid and B-spline
Sun, Zheng
Niu, Liyong
Liu, Bin
Wang, Kedian
Li, Bo
Mei, Xuesong
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2022, 121 (3-4): : 2747 - 2757

← 1 2 →