Investigation of vibrating jaw crusher experimental variables

被引:0
|
作者
Haddad, Jamil [1 ]
Alfaqs, Fadi [1 ]
Al-quraan, Tareq [1 ]
Ikhries, Ibrahim I. [1 ]
机构
[1] Al Balqa Appl Univ, Amman, Jordan
来源
MINING OF MINERAL DEPOSITS | 2023年 / 17卷 / 03期
关键词
jaw crusher; crushing; vibration; milling; material; DYNAMIC-BEHAVIOR;
D O I
10.33271/mining17.03.049
中图分类号
TD [矿业工程];
学科分类号
0819 ;
摘要
Purpose. Current research focuses on studying experimentally various parameters affecting the particle size produced in a vibrating jaw crusher developed and implemented at Al-Balqa Applied University. The main purpose is to find the optimal conditions at which the jaw crusher under study works. Methods. The jaw crusher angle and rotating mass type are considered to study all particle sizes and reduction ratios obtained for three different motor operation speeds: 1500, 2000, and 2500 rpm. Coarse aggregate weighing 900 g with 26 mm particle size is fed into the jaw crusher, which produces several particle sizes (19, 12.5, 9.5, 4.75, and less than 4.75 mm). Furthermore, the mass of the particles is measured and the particle size reduction is calculated. Findings. It has been found that the jaw crusher angle, rotating mass type, and the motor operation speed play an important role in both reducing the amount of mass and reducing the size of each particle produced. In addition, it has been determined that operation at a speed of 2000 rpm provides a significant change in both mass and size reduction of each particle size considered. Originality. The originality of this research lies in its experimental investigation of the effects of various parameters on particle size reduction in a vibrating jaw crusher, as well as in the introduction of a new design that uses one motor to drive two plates operating at different speeds and in opposite directions. Practical implications. The findings can be used to optimize the design and operation of jaw crushers in various industries, including metallurgical, quarry, and mining industries, where these crushers are widely used. The results of this study can also serve as a basis for future research on particle size reduction in other types of crushers and milling equipment.
引用
收藏
页码:49 / 55
页数:7
相关论文
共 50 条
  • [1] DYNAMIC BEHAVIOUR OF A VIBRATING JAW CRUSHER FOR DISINTEGRATION OF HARD MATERIALS
    Wolny, S.
    ARCHIVES OF METALLURGY AND MATERIALS, 2013, 58 (03) : 883 - 886
  • [2] A Vibrating Jaw Crusher with Auteresonant Electric Motor Drive of Swinging Movement
    Zagrivniy, E. A.
    Poddubniy, D. A.
    ALL-RUSSIAN RESEARCH-TO-PRACTICE CONFERENCE ECOLOGY AND SAFETY IN THE TECHNOSPHERE, 2018, 115
  • [3] Self-Synchronization of a Vibrating Jaw Crusher with Allowance for Interaction with the Medium Processed
    A. E. Shokhin
    Journal of Machinery Manufacture and Reliability, 2020, 49 : 500 - 510
  • [4] Self-Synchronization of a Vibrating Jaw Crusher with Allowance for Interaction with the Medium Processed
    Shokhin, A. E.
    JOURNAL OF MACHINERY MANUFACTURE AND RELIABILITY, 2020, 49 (06) : 500 - 510
  • [5] Power determination and the experimental analysis formula for jaw crusher
    Wu, Gancheng
    Wuhan Gangtie Xueyuan Xuebao/Journal of Wuhan Iron and Steel University, 1997, 20 (02): : 185 - 188
  • [6] The jaw crusher series
    不详
    CFI-CERAMIC FORUM INTERNATIONAL, 2007, 84 (03): : 2 - 3
  • [7] Experimental research of oscillation parameters of vibrating-rotor crusher
    Honcharuk, Inna
    Kupchuk, Ihor
    Solona, Olena
    Tokarchuk, Oleksiy
    Telekalo, Natalia
    PRZEGLAD ELEKTROTECHNICZNY, 2021, 97 (03): : 97 - 100
  • [8] Experimental research on crushing force and its distribution feature in jaw crusher
    Cao Jinxi
    Qin Zhiyu
    Rong Xingfu
    Yang Shichun
    ICIEA 2007: 2ND IEEE CONFERENCE ON INDUSTRIAL ELECTRONICS AND APPLICATIONS, VOLS 1-4, PROCEEDINGS, 2007, : 2143 - 2147
  • [9] JAW CRUSHER OF DOUBLE CRUSHING
    Dashesevich, A. I.
    JOURNAL OF MINING INSTITUTE, 2009, 181 : 156 - 157
  • [10] Material Flow in Jaw Crusher
    CAO Jinxi RONG Xingfu YANG Shichun College of Mechanical EngineeringTaiyuan University of TechnologyTaiyuan China
    武汉理工大学学报, 2006, (S2) : 474 - 478