High-stress abrasive wear performance of medium-carbon direct-quenched and partitioned, carbide-free bainitic, and martensitic steels

被引：14

作者：

Haiko, Oskari ^{[1
]}

Pallaspuro, Sakari ^{[1
]}

Javaheri, Vahid ^{[1
]}

Kaikkonen, Pentti ^{[1
]}

Ghosh, Sumit ^{[1
]}

Valtonen, Kati ^{[2
]}

Kaijalainen, Antti ^{[1
]}

Komi, Jukka ^{[1
]}

机构：

[1] Univ Oulu, Ctr Adv Steels Res, Mat & Mech Engn, FI-90014 Oulu, Finland

[2] Tampere Univ, Tampere Wear Ctr, Mat Sci & Environm Engn, FI-33720 Tampere, Finland

来源：

WEAR | 2023年 / 526卷

基金：

芬兰科学院;

关键词：

Steel; Microstructure; Abrasion; Wear testing; RETAINED AUSTENITE; BEHAVIOR; MICROSTRUCTURE; STABILITY; RESISTANCE; XRD;

D O I：

10.1016/j.wear.2023.204925

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

Experimental steels, a direct-quenched and partitioned (DQP) steel and a carbide-free bainitic steel (CFB), were tested along with a commercial martensitic 500 HB grade wear resistant steel in high-stress abrasive conditions. The three steels had different microstructures consisting of varying fractions and morphologies of martensite, retained austenite, and bainitic ferrite. The results showed that the CFB steel had a lower mass loss compared to the martensitic 500 HB steel with a similar hardness level. The DQP steel had a higher initial hardness and outperformed the other two steels. Wear surface characterization revealed that the investigated steels had significant work hardening of the wear surface, except with different mechanisms. Transformation induced plasticity (TRIP) increased the hardness of the DQP and CFB steels, while the fully martensitic 500 HB had more white layer formation on the wear surface resulting in increased hardness.

引用

页数：11

共 26 条

[1] Characteristics of carbide-free medium-carbon bainitic steels in high-stress abrasive wear conditions
Haiko, Oskari
Kaikkonen, Pentti
Somani, Mahesh
Valtonen, Kati
Komi, Jukka
WEAR, 2020, 456
[2] Microstructure evolution of carbide-free bainitic steels under abrasive wear conditions
Gola, A. M.
Ghadamgahi, M.
Ooi, S. W.
WEAR, 2017, 376 : 975 - 982
[3] The rolling/sliding wear performance of high silicon carbide-free bainitic steels
Chang, LC
WEAR, 2005, 258 (5-6) : 730 - 743
[4] Mechanical Behavior of Carbide-free Medium Carbon Bainitic Steels
Xiaoxu Zhang
Guang Xu
Xiang Wang
David Embury
Olivier Bouaziz
Gary R. Purdy
Hatem S. Zurob
Metallurgical and Materials Transactions A, 2014, 45 : 1352 - 1361
[5] Mechanical Behavior of Carbide-free Medium Carbon Bainitic Steels
Zhang, Xiaoxu
Xu, Guang
Wang, Xiang
Embury, David
Bouaziz, Olivier
Purdy, Gary R.
Zurob, Hatem S.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2014, 45A (03): : 1352 - 1361
[6] Low cycle fatigue behavior in a medium-carbon carbide-free bainitic steel
Kang, J.
Zhang, F. C.
Long, X. Y.
Lv, B.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 666 : 88 - 93
[7] Influence of niobium microalloying on the thermal stability of medium-carbon carbide-free bainitic steel
Yu, Xinpan
Wu, Huibin
Zhang, Youyou
Yuan, Rui
Gu, Yang
Feng, Yuhui
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2021, 12 : 487 - 499
[8] Impact abrasive wear behaviour of the multiphase microstructure in a medium carbon quenched and partitioned bainitic steel
Li, Qiangguo
Zhang, Yanan
Luo, Hong
WEAR, 2023, 518
[9] Evolution of tensile properties with transformation temperature in medium-carbon carbide-free bainitic steel
Long, Xiaoyan
Zhao, Gengcen
Zhang, Fucheng
Xu, Shan
Yang, Zhinan
Du, Guojun
Branco, Ricardo
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 775 (775):
[10] Influence of fracture toughness on two-body abrasive wear of nanostructured carbide-free bainitic steels
Moghaddam, P. Valizadeh
Rinaudo, M.
Hardell, J.
Vuorinen, E.
Prakash, B.
WEAR, 2020, 460 (460-461)

← 1 2 3 →