Effect of Cutting Parameters on Surface Roughness and Cutting Forces in Hard Turning of 1.2367 Hot Work Tool Steel

被引：1
|
作者：
Erdem, Sumeyye [1 ]
Ozdemir, Mustafa [2 ]
Rafighi, Mohammad [3 ]
Yavuz, Mehtap [4 ]
机构：
[1] Karamanoglu Mehmetbey Univ, Tekn Bilimler Meslek Yuksekokulu, Karaman, Turkey
[2] Yozgat Bozok Univ, Yozgat Meslek Yuksekokulu, Yozgat, Turkey
[3] Turk Hava Kurumu Univ, Makine Muhendisligi Bolumu, Ankara, Turkey
[4] Cankiri Karatekin Univ, Meslek Yuksekokulu, Cankiri, Turkey
来源：
JOURNAL OF POLYTECHNIC-POLITEKNIK DERGISI | 2023年 / 26卷 / 03期
关键词：
1.2367 hot tool steel; surface roughness; cutting forces; carbide insert; taguchi method; FEED RATE; SPEED;
D O I：
10.2339/politeknik.1059568
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In this study, the effects of different cutting parameters on surface roughness (Ra) and cutting force were investigated in dry hard turning of 1.2367 hardened (55 HRC) hot tool steel. In this experimental study, the Taguchi method was used for the design of experiments, and a constant cutting depth; three different cutting speeds, and three different feed rates were selected as cutting parameters. The effects of cutting parameters on surface roughness and cutting forces were evaluated by performing an analysis of variance (ANOVA). According to the results, it was observed that the surface roughness value increased depending on the increase in the feed rate. On the other hand, the influence of cutting speed on the surface roughness was negligible. It was seen that the most effective parameter on the radial force (Fy), tangential force (Fy), and feed force (Fz) was the feed rate.
引用
收藏
页码：1071 / 1077
页数：9
相关论文
共 50 条
  • [1] Investigation of the effect of cutting parameters on cutting force, surface roughness and chip shape in turning of Sleipner cold work tool steel
    Ozlu, Baris
    [J]. JOURNAL OF THE FACULTY OF ENGINEERING AND ARCHITECTURE OF GAZI UNIVERSITY, 2021, 36 (03): : 1242 - 1251
  • [2] Experimental investigations of cutting parameters influence on cutting forces and surface roughness in finish hard turning of MDN250 steel
    Lalwani, D. I.
    Mehta, N. K.
    Jain, P. K.
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 206 (1-3) : 167 - 179
  • [3] REGRESSION MODELING OF CUTTING PARAMETERS' EFFECT TO CUTTING FORCES AND HOLE SURFACE QUALITIES IN DRILLING OF DIEVAR HOT WORK TOOL STEEL
    Ozkul, Iskender
    Buldum, Berat Baris
    Akkurt, Adnan
    [J]. PAMUKKALE UNIVERSITY JOURNAL OF ENGINEERING SCIENCES-PAMUKKALE UNIVERSITESI MUHENDISLIK BILIMLERI DERGISI, 2013, 19 (01): : 1 - 9
  • [4] On the prediction of surface roughness in the hard turning based on cutting parameters and tool vibrations
    Hessainia, Zahia
    Belbah, Ahmed
    Yallese, Mohamed Athmane
    Mabrouki, Tarek
    Rigal, Jean-Francois
    [J]. MEASUREMENT, 2013, 46 (05) : 1671 - 1681
  • [5] Analysis and prediction of tool wear, surface roughness and cutting forces in hard turning with CBN tool
    Samir Khamel
    Nouredine Ouelaa
    Khaider Bouacha
    [J]. Journal of Mechanical Science and Technology, 2012, 26 : 3605 - 3616
  • [6] Analysis and prediction of tool wear, surface roughness and cutting forces in hard turning with CBN tool
    Khamel, Samir
    Ouelaa, Nouredine
    Bouacha, Khaider
    [J]. JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY, 2012, 26 (11) : 3605 - 3616
  • [7] Analysis of cutting forces and roughness during hard turning of bearing steel
    Bouziane, Abderrahim
    Boulanouar, Lakhdar
    Azizi, Mohamed Walid
    Keblouti, Ouahid
    Belhadi, Salim
    [J]. STRUCTURAL ENGINEERING AND MECHANICS, 2018, 66 (03) : 285 - 294
  • [8] SURFACE ROUGHNESS AND CUTTING FORCES IN CRYOGENIC TURNING OF CARBON STEEL
    Yap, T. C.
    Sivaraos
    Lim, C. S.
    Leau, J. W.
    [J]. JOURNAL OF ENGINEERING SCIENCE AND TECHNOLOGY, 2015, 10 (07): : 911 - 920
  • [9] SURFACE ROUGHNESS AND CUTTING FORCES IN TURNING OF TOOL STEEL WITH MIXED CERAMIC AND CUBIC BORON NITRIDE CUTTING TOOLS
    Yalcin, Bekir
    [J]. TRANSACTIONS OF THE CANADIAN SOCIETY FOR MECHANICAL ENGINEERING, 2015, 39 (02) : 323 - 336
  • [10] Investigation and modeling of cutting forces and surface roughness when hard turning of AISI 52100 steel with mixed ceramic tool: cutting conditions optimization
    Meddour, I.
    Yallese, M. A.
    Khattabi, R.
    Elbah, M.
    Boulanouar, L.
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2015, 77 (5-8): : 1387 - 1399
12345