Study on Oblique Penetration of Metal Plate by Naval Gun Semi-armor-piercing Simulation Projectile

被引：0
|
作者：
Pei G. [1 ,2 ]
Nie J. [1 ]
Wang Q. [3 ]
Jiao Q. [1 ]
Du Z. [2 ]
Li Y. [1 ]
机构：
[1] State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing
[2] Unit 92942 of PLA, Beijing
[3] System Engineering Research Institute, China State Shipbuilding Corporation Limited, Beijing
来源：
Binggong Xuebao/Acta Armamentarii | 2024年 / 45卷 / 03期
关键词：
homogeneous plate; naval gun; oblique penetration; residual velocity; semi-armor-piercing projectile;
D O I：
10.12382/bgxb.2022.0793
中图分类号：
学科分类号：
摘要：
Ship gun is one of the main weapons for attacking the targetsat sea, air and shore, and the penetration ability of semi-armor-piercing projectile for ship gun is an important index of evaluating its damage ability. Carrying out live-ship firing test is costly and lack of opportunities. In order to study the penetration ability of naval gun semi-armor-piercing projectile, a semi-armor-piercing simulation projectile is designed by referring to OTO Melara 127 mm ammunition used by US MK-45 naval gun. On the basis of experiment, numerical simulation and empirical formula, the damage mode and crevasse size of target plate are analyzed. The experimental results show that, under the two plate inclination angles of 45° and 60° and two target velocities of 385 m / s and 500 m / s, the semi-armor-piercing simulation projectile has sufficient penetration ability to 12 mm thick E36 steel plate, and the damage mode of simulation projectile to target plate is a thrust destruction. The average size of the crevasse is 1.25 times the diameter of the projectile. The simulated results show that the calculated results including the residual velocity and breach are reasonably agreed with the experimental results. The calculated results of Thor’s formula are relatively close to the experimental results. After parameter optimization, the residual velocity error obtained by the experiment, empirical formula and simulation does not exceed 10% . © 2024 China Ordnance Industry Corporation. All rights reserved.
引用
收藏
页码：731 / 743
页数：12
相关论文
共 22 条
  • [1] MIAO R, WANG W L, WU S Y, Et al., Influence of hole size of semi-armor-piercing warhead on ship’s cabin implosion effect, Chinese Journal of High Pressure Physics, 32, 6, pp. 156-162, (2018)
  • [2] DU H C, ZHANG X F, LIU C, Et al., Trajectory characteristics of projectile obliquely penetrating into steel target with multi-layer space structure, Acta Armamentarii, 42, 6, pp. 1204-1214, (2021)
  • [3] DUAN J, ZHOU G, TIAN C Y, Et al., Design and pnentration performance of a semi-armor-piercing penetrator, Journal of Experimental Mechanics, 26, 4, pp. 383-390, (2011)
  • [4] ZHANG N., The research of ballistic deflection about penetrating stiffened plates, (2016)
  • [5] DUAN Z P, ZHANG Z G, LI J Z, Et al., The experimental research for warhead vertically penetrating homogeneous and ribbings structural target, Journal of Projectiles, Rockets, Missiles and Guidance, 25, 2, pp. 148-150, (2005)
  • [6] ZHU D J, WANG Q Z, SUN D C, Et al., Numerical simulation study of penetration on target plate by armor-piercing bullet, Ship & Boat, 149, 5, pp. 40-45, (2014)
  • [7] JIA Z D, ZHANG Z., Numerical simulation study on comprehensive damage of pure steel target by semi-piercing projectile penetration and explosion, Journal of Sichuan Ordnance, 41, 5, pp. 96-100, (2020)
  • [8] HUANG Q, ZHOU T, BAI Y, Et al., Ballistic performance of projectile penetrating large-spaced multi-layer plates at variable angle-of-attack, Acta Armamentarii, 37, pp. 251-257, (2016)
  • [9] TANG X Z, WANG Z J, DONG L Y, Et al., Numerical simulation analysis of projectile oblique impact target plate, Journal of Sichuan Ordnance, 40, 6, pp. 47-50, (2019)
  • [10] WANG Y N, ZHANG J W, WANG Z, Et al., Equivalent method of 921A steel and Q345 steel target plate under truncated ovoid projectile penetration based on plate thickness compensation, Acta Armamentarii, 42, 11, pp. 2465-2475, (2021)
123