Effect of pre-strain on tensile mechanical properties of 2195 aluminum-lithium alloy

被引：1

作者：

Zhang Y. ^{[1
,2
]}

Ye L. ^{[1
,2
]}

Dong Y. ^{[1
,2
]}

Zou G. ^{[1
,2
]}

Li J. ^{[1
,2
]}

Yang X. ^{[1
,2
]}

机构：

[1] School of Material Science and Engineering, Central South University, Changsha

[2] Key Laboratory of Nonferrous Metal Materials Science and Engineering, Ministry of Education, Central South University, Changsha

来源：

Zhongguo Youse Jinshu Xuebao/Chinese Journal of Nonferrous Metals | 2024年 / 34卷 / 03期

基金：

中国国家自然科学基金;

关键词：

2195 Al-Li alloy; digital image correlation; strain concentration phenomenon; stretching pre-strain; tensile mechanical properties;

D O I：

10.11817/j.ysxb.1004.0609.2023-44427

中图分类号：

学科分类号：

摘要：

The effects of different stretching pre-strains on the tensile mechanical properties of 2195 aluminum-lithium alloy after aging at 155 ℃ were studied by hardness test, room temperature tensile test, electron backscatter diffraction analysis (EBSD), transmission electron microscopy (TEM) and digital image correlation (DIC). The results show that the ultimate tensile stresses at the stretching pre-strain of 2%, 4%, 6% and 8% are 560.4 MPa, 570.8 MPa, 573.6 MPa and 575.9 MPa. With the increase of stretching pre-strain, the strength of the alloy continues to increase, which is because the dislocation is a favorable nucleation point for the strengthened phase T1 phase, and the increase of stretching pre-strain increases the dislocation density and the number density of T1 phase. However, with the increase of stretching pre-strain, the strength increase amplitude of stretching pre-strain on the alloy gradually decreases, which is mainly caused by entanglement and accumulation of dislocation and precipitation of phase nucleation points. As the stretching pre-strain increases from 2% to 8%, the elongation of the alloy decreases from 9.6% to 6.4%. It can be observed that the increase of stretching pre-strain makes the strain concentration phenomenon in the tensile process advance and the necking stability decreases by digital image correlation. This is due to the large stretching pre-strain will cause the strain distribution of the alloy in the stretching pre-strain to be uneven, and broken deformation microstructure grains appear in the alloy. The grain orientation of these deformation microstructure grains are different from other grain around them, which is more conducive to the initiation and propagation of microcracks. Therefore, considering the tensile mechanical properties of 2195 aluminum-lithium alloy under different stretching pre-strain, 4% stretching pre-strain can make 2195 aluminum-lithium alloy achieve the best strong plastic matching, with ultimate tensile stress of 570.8 MPa, yield stress of 543.4 MPa and elongation of 8.7%. © 2024 Central South University of Technology. All rights reserved.

引用

页码：725 / 738

页数：13

共 33 条

[1] ABD EL-ATY A, XU Y, GUO X Z, Et al., Strengthening mechanisms, deformation behavior, and anisotropic mechanical properties of Al-Li alloys: A review[J], Journal of Advanced Research, 10, (2018)
[2] DENG Y L, ZHANG X M., Development of aluminium and aluminium alloy, The Chinese Journal of Nonferrous Metals, 29, 9, (2019)
[3] RIOJA R J, LIU J., The evolution of Al-Li base products for aerospace and space applications, Metallurgical and Materials Transactions A, 43, 9, (2012)
[4] WILLIAMS J C, STARKE E A JR., Progress in structural materials for aerospace systems, Acta Materialia, 51, 19, (2003)
[5] KIM I S, SONG M Y, KIM J H, Et al., Effect of added Mg on the clustering and two-step aging behavior of Al − Cu alloys, Materials Science and Engineering A, 798, (2020)
[6] CHEN H, CHEN Z, JI G, Et al., Experimental and modelling assessment of ductility in a precipitation hardening AlMgScZr alloy, International Journal of Plasticity, 139, (2021)
[7] KANG S J, KIM T H, YANG C W, Et al., Atomic structure and growth mechanism of T<sub>1</sub> precipitate in Al−Cu−Li−Mg− Ag alloy[J], Scripta Materialia, 109, (2015)
[8] WANG S, ZHANG C, LI X, Et al., First-principle investigation on the interfacial structure evolution of the δ′/θ′/δ′ composite precipitates in Al-Cu-Li alloys[J], Journal of Materials Science & Technology, 58, (2020)
[9] DORIN T, DESCHAMPS A, DE GEUSER F, Et al., Quantification and modelling of the microstructure/strength relationship by tailoring the morphological parameters of the T<sub>1</sub> phase in an Al−Cu−Li alloy[J], Acta Materialia, 75, (2014)
[10] MALIKOV A, ORISHICH A, VITOSHKIN I, Et al., Effect of the structure and the phase composition on the mechanical properties of Al-Cu-Li alloy laser welds, Materials Science and Engineering A, 809, (2021)

← 1 2 3 4 →