Friction welding of 6061 aluminum alloy and S45C carbon steel using insert metal

被引：0

作者：

Ochi, Hiizu ^{[1
]}

Ogawa, Koichi ^{[1
]}

Yamamoto, Yoshiaki ^{[1
]}

Habe, Mitsutoshi ^{[1
]}

Suga, Yasuo ^{[1
]}

机构：

[1] Osaka Inst of Technology, Osaka, Japan

来源：

Keikinzoku/Journal of Japan Institute of Light Metals | 1994年 / 44卷 / 06期

关键词：

Aluminum alloys - Carbon steel - Interfaces (materials) - Process control - Strength of materials - Welds;

D O I：

暂无

中图分类号：

学科分类号：

摘要：

Friction welding of a 6061 aluminum alloy to a S45C carbon steel was carried out using the insert metal of a 1050 aluminum. Optimum thickness of the insert metal, friction pressure, forge pressure, friction time and rotational speed of welding conditions were determined as 4 mm, 90 MPa, 300 MPa, 1.2 s and 2250 rpm, respectively. When the insert metal turned into a thin (20 to approximately 30 μm) and homogeneous layer at the weld interface, the maximum joint efficiency of tensile strength was obtained and was about 95%. Successful welds were obtained by taking each optimum welding condition even if the thickness of the insert metal was varied from 2 to 6 mm.

引用

页码：320 / 324

共 50 条

[1] Friction welding of 2017 aluminum alloy and S45C carbon steel using insert metal
Ogawa, Koichi
Ochi, Hiizu
Yamamoto, Yoshiaki
Habe, Mitsutoshi
Iwamoto, Takuya
Suga, Yasuo
Keikinzoku Yosetsu/Journal of Light Metal Welding and Construction, 1994, 32 (01): : 3 - 11
[2] Friction welding of A 6061 aluminum alloy and S45C carbon steel
Shinoda, T
Kawata, S
DESIGNING, PROCESSING AND PROPERTIES OF ADVANCED ENGINEERING MATERIALS, PTS 1 AND 2, 2004, 449-4 : 437 - 440
[3] Friction Stir Spot Butt Welding of Dissimilar S45C Steel and 6061-T6 Aluminum Alloy
Gao, Kun
Zhang, Shengwei
Mondal, Mounarik
Basak, Soumyabrata
Hong, Sung-Tae
Shim, Heechan
METALS, 2021, 11 (08)
[4] Impact tensile strength of 6061 aluminum alloy/S45C carbon steel friction welded butt joints
Yokoyama, Takashi
Yamaguchi, Masashi
Keikinzoku/Journal of Japan Institute of Light Metals, 1999, 49 (11): : 535 - 541
[5] Friction welding characteristics of Al-Mg aluminum alloy (A5056) and carbon steel (S45C)
Kobayashi, A
Machida, M
Hukaya, S
Suzuki, M
JSME INTERNATIONAL JOURNAL SERIES A-SOLID MECHANICS AND MATERIAL ENGINEERING, 2003, 46 (03) : 452 - 459
[6] Welding properties between 6063 aluminum and S45C steel by friction stir
Yasui, T
Shimoda, Y
Tsubaki, M
Fukumoto, M
PROCEEDINGS OF THE FIFTEENTH (2005) INTERNATIONAL OFFSHORE AND POLAR ENGINEERING CONFERENCE, VOL 4, 2005, : 39 - 43
[7] Friction welding of 6061 aluminum alloy pipe to S25C carbon steel pipe
Kawai, G.
Ogawa, K.
Tokisue, H.
International Journal of Offshore and Polar Engineering, 1998, 8 (02): : 144 - 147
[8] Microstructural control and mechanical properties in friction stir welding of medium carbon low alloy S45C steel
Imam, Murshid
Ueji, Rintaro
Fujii, Hidetoshi
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2015, 636 : 24 - 34
[9] Numerical analysis of linear friction welding process of steel S45C
Chen, Liang
Li, Wenya
Ma, Tiejun
Ma, Caixia
Hanjie Xuebao/Transactions of the China Welding Institution, 2010, 31 (02): : 91 - 94
[10] Welding Microstructure and Tensile Properties of S45C Carbon Steel
Kuo, Chin-Guo
Chang, Jin-Chung
Hung, Yi-Hsuan
Kang, Yen-Tien
Kao, Chen-Yang
Chen, Jung-Hsuan
SENSORS AND MATERIALS, 2018, 30 (03) : 675 - 681

← 1 2 3 4 5 →