Passivation Behavior of Laser Selective Melted 316L Stainless Steel in Sulphuric Acid Containing Chloride Ion Solution

被引：0
|
作者：
Li F. [1 ]
Liu Z. [1 ]
Qiao Y. [1 ]
Yang L. [1 ]
Lu D. [2 ]
Tang Y. [2 ]
机构：
[1] School of Materials Science and Technology, Jiangsu University of Science and Technology, Zhenjiang
[2] Marine Equipment and Technology Institute, Jiangsu University of Science and Technology, Zhenjiang
来源：
Cailiao Yanjiu Xuebao/Chinese Journal of Materials Research | 2024年 / 38卷 / 03期
关键词：
316L stainless steel; electrochemical tests; materials failure and protection; passivation behavior;
D O I：
10.11901/1005.3093.2023.119
中图分类号：
学科分类号：
摘要：
The open-circuit potential, electrochemical impedance spectroscopy, potentiodynamic polarization, potentiostats polarization, current-time transient measurements, Mott-Schottky analysis, X-ray photoelectron spectroscopy (XPS), Electron Back-Scattered Diffraction(EBSD)methods were used to investigate the passivation behavior of 316L stainless steel fabricated by laser selective melted (SLM 316L) in 0.05 mol/L H2SO4 + 0.2 mol/L NaCl solution. The results were compared with commercial rolled 316L stainless steel (R 316L). The results showed that the nucleation of passivation film follows continuous mechanism for the both stainless steel. However, the SLM 316L stainless steel has smaller grain size and higher grain boundary density than those of R 316L stainless steel. Therefore, the grow rate of passivation film is fast. The SLM 316L stainless steel took place transpassivation dissolution, while R 316L stainless steel took place pitting corrosion. The SLM 316L stainless steel has better corrosion resistance. The main reasons are the SLM 316L stainless steel has much more low angle grain boundaries without ferrite. Moreover, the passivation film of SLM 316L stainless steel has lower carrier density, lower ratio of O2-/OH-, lower content of NiO and higher content of Cr2O3 compared with R 316L stainless steel. © 2024 Chinese Journal of Materials Research. All rights reserved.
引用
收藏
页码：221 / 231
页数：10
相关论文
共 42 条
  • [1] Bacciaglla A, Ceruti A, Liverani A, Et al., Towards large parts manufacturing in additive technologies for aerospace and automotive applications, Procedia Computer Science, 200, (2022)
  • [2] Melenka G W, Cheung B K O, Schofield J S, Et al., Evaluation and prediction of the tensile properties of continuous fiber-reinforced 3d printed structures, Compos. Struct, 153, (2016)
  • [3] Daminabo S C, Goel S, Grammatikos S A, Et al., Fused deposition modeling-based additive manufacturing (3D printing): techniques for polymer material systems, Mater. Today., Chem, 16, (2020)
  • [4] Guo Q, Zhao C, Qu M, Et al., In-situ characterization and quantification of melt pool variation under constant input energy density in laser powder bed fusion additive manufacturing process [J], Addit. Manuf, 28, (2019)
  • [5] Li R, Niu P, Yuan T., Selective laser melting of an equiatomic CoCrFeMnNi high-entropy alloy: Processability, non-equilibrium microstructure and mechanical property, J. Alloy. Compd, 746, (2018)
  • [6] Lodhi M J K, Iams A D, Sikora E, Et al., Microstructural features contributing to macroscopic corrosion: The role of oxide inclusions on the corrosion properties of additively manufactured 316L stainless steel [J], Corros. Sci, 203, (2022)
  • [7] Zhang Z, Yuan X, Zhao Z, Et al., Electrochemical noise comparative study of pitting corrosion of 316L stainless steel fabricated by selective laser melting and wrought, J. Electroanal. Chem, 894, (2021)
  • [8] Zhao C L, Bai Y, Zhang Y, Et al., Influence of scanning strategy and building direction on microstructure and corrosion behaviour of selective laser melted 316L stainless steel, Mater. Design, 209, (2021)
  • [9] Zhao Y, Xiong H, Li X, Et al., Improved corrosion performance of selective laser melted stainless steel 316L in the deep-sea environment [J], Corros. Commun, 2, (2021)
  • [10] Laleh M, Hughes A E, Xu W, Et al., Unexpected erosion-corrosion behaviour of 316L stainless steel produced by selective laser melting [J], Corros. Sci, 155, (2019)
12345