Experimental investigation into axial compressive behavior of cold-formed thin-walled steel columns with lipped channel and openings

被引：11

作者：

Yao Y.-H. ^{[1
]}

Wu Z.-Y. ^{[1
]}

Cheng B. ^{[1
]}

Deng J.-B. ^{[1
]}

机构：

[1] School of Civil Engineering, Harbin Institute of Technology, Harbin 150090, Heilongjiang

来源：

Huanan Ligong Daxue Xuebao/Journal of South China University of Technology (Natural Science) | 2011年 / 39卷 / 09期

关键词：

Cold-formed thin-walled steel; Distortional buckling; Experimental investigation; Finite element method; Lipped channel section; Opening;

D O I：

10.3969/j.issn.1000-565X.2011.09.011

中图分类号：

学科分类号：

摘要：

In order to investigate the compression behavior of the cold-formed thin-walled steel columns with lipped channel, intermediate stiffener and openings in the web, 16 axial compressive members, including the short and the medium-length columns in two section forms, were experimentally analyzed in the aspects of bearing capacity and buckling mode. The results show that all of the specimens fail due to the distortional buckling and the medium-length columns have additional overall bending around the weak axis, that the openings in the web result in the changes of buckling modes of the members and the local bucklings of the plates occur around the openings, and that, due to the effects of the openings, the bearing capacities of the specimens decrease and the decrement of the bearing capacity of the short column is greater than that of the medium-length one. Moreover, it is found that, for the specimens in the same test group, the columns with larger initial distortional imperfections are of lower bearing capacities and greater deformations induced by the distortional bucklings, and that the openings generally enhance the deformations corresponding to the ultimate bearing capacity. In addition, all of the tested specimens are simulated by means of the finite element method, finding that the simulated results accord well with the experimental ones.

引用

页码：61 / 67

页数：6

共 12 条

[1] Yu W.W., Cold-Formed Steel Design, (2000)
[2] Laboube R.A., Yu W.W., Recent research and developments in cold-formed steel framing, Thin-Walled Structures, 32, 1-3, pp. 19-39, (1998)
[3] Laboube R.A., Yu W.W., Langan J.E., Et al., Cold-formed steel webs with openings: Summary report, Thin-Walled Structures, 27, 1, pp. 79-84, (1997)
[4] Schafer B.W., Review: The direct strength method of cold-formed steel member design, Journal of Constructional Steel Research, 64, 7-8, pp. 766-778, (2008)
[5] Hu B.-X., Liu Y.-J., Ultimate load capacity of cold-formed lipped channel member with web perforation subjected to axial compression, Journal of Jiangsu University: Natural Science Edition, 28, 3, pp. 258-261, (2007)
[6] Zhao G.-P., He B.-K., An experiment study on post-buckling behaviour of cold-formed lipped channel with perforated web, Journal of Xi'an University of Architecture & Technology, 21, 2, pp. 23-30, (1989)
[7] Moen C., Schafer B.W., Experiments on cold-formed steel columns with holes, Thin-Walled Structures, 46, 10, pp. 1164-1182, (2008)
[8] Wang C.-G., Zhang Y.-C., Zhang Z.-N., Experimental investigation on channel columns with inclined simple edge stiffeners under compression loading, Journal of Building Structures, 27, 3, pp. 1-9, (2006)
[9] (2009)
[10] Dubina D., Ungureanu V., Effect of imperfections on numerical simulation of instability behaviour of cold-formed steel members, Thin-Walled Structures, 40, 3, pp. 239-262, (2002)

← 1 2 →