Study on calibration method of rotary axis based on vision measurement

被引：0
|
作者：
Bi C. [1 ]
Hao X. [1 ]
Liu M. [1 ]
Fang J. [1 ]
机构：
[1] Aviation Key Laboratory of Science and Technology on Precision Manufacturing Technology, Beijing Precision Engineering Institute for Aircraft Industry, Beijing
来源：
| 2020年 / Chinese Society of Astronautics卷 / 49期
关键词：
Coordinate measuring machine; Film cooling hole; Rotary table; Vision measurement;
D O I：
10.3788/IRLA202049.0413004
中图分类号：
学科分类号：
摘要：
For the purpose of inspecting the film cooling holes on high-pressure turbine blade in a rapid and accurate manner, a non-contact four-axis vision coordinate measuring system was designed and established in the paper. With regard to the determination difficulty of the spatial location of the rotary axis, a calibration method based on vision measurement was proposed in the paper, which fully considered the imaging characteristics of industrial CCD used in the system. In the calibrating procedure, a specially designed cuboid mental block was applied as the target. Through the coordination between the turntable and the coordinate measuring machine, the industrial CCD focused on the block surface and then captured the sharp edges of the block. And then, the spatial orientation of the rotary axis in the machine coordinate system could be determined by edge extraction, pixel distance calculation, physical distance conversion and algebraic operation etc. Finally, a gauge block was selected to be inspected by the measuring system to verify the calibration method and results, whose nominal size was 80 mm. As the experimental results showed, the measuring errors were all smaller than ±0.01 mm. Therefore, the calibration method of rotary axis proposed in the paper showed higher calibration precision and repeatability, which could meet the inspecting requirements of the shape and position parameters of film cooling holes. © 2020, Editorial Board of Journal of Infrared and Laser Engineering. All right reserved.
引用
收藏
相关论文
共 15 条
  • [1] Dong Y., Wu Z., Li X., Et al., Current situation and development trend of processing and measurement technology for turbine blade film cooling hole, Aeronautical Manufacturing Technology, 61, 13, pp. 16-25, (2018)
  • [2] Zeng L., Chen P., Li X., Et al., Influence of simplifications of blade in gas turbine on film cooling performance, Applied Thermal Engineering, 128, pp. 877-886, (2018)
  • [3] Wang C., Liu T., Mu X., Et al., Research on aero engine blade film hole measuring technology, Metrology & Measurement Technology, 32, 5, pp. 27-30, (2012)
  • [4] Qin D., Wang C., Shi Y., Et al., Parameter calibration research of the turntable for 4-axis 3D laser measuring system, Journal of Huazhong University of Science & Technology, 37, 6, pp. 129-132, (2009)
  • [5] Xu Y., Yang Q., Huai J., Calibration of the axis of the turntable in 4-axis laser measuring system and registration of multi-view, Chinese Journal of Lasers, 32, 5, pp. 659-662, (2005)
  • [6] Ding H., Xu Y., Design of 3D rotary laser scanning and measuring system, Modern Electronics Technology, 34, 8, pp. 164-166, (2011)
  • [7] Tan W., Zhang Q., Li X., Et al., The calibration method of rotary axis for the θFXZ measuring machine, Mechanical Science and Technology for Aerospace Engineering, 35, 2, pp. 285-289, (2016)
  • [8] Li X., Li X., Zhu J., Et al., Study on the calibration strategy of the rotary axis for the measuring machine with the θFXZ structure, Mechanical Science and Technology for Aerospace Engineering, 32, 11, pp. 1591-1594, (2013)
  • [9] He W., Ma H., Guo Y., Et al., Research on accurate calibration of shaft in non-contact optical measurement of aviation blades, Journal of Heilongjiang University of Science & Technology, 27, 2, pp. 181-185, (2017)
  • [10] Huang J., Xu B., A machine vision system for position measurement of small holes on spherical surface, Nanotechnology and Precision Technology, 14, 1, pp. 28-34, (2016)
12