Penetration resistance and fracture mechanism of high-hardness polyurea coating

被引：0
|
作者：
Zhang P. [1 ,2 ]
Zhao P. [2 ]
Wang Z. [1 ]
Zhang L. [2 ]
Ren J. [3 ]
Xu Y. [3 ]
机构：
[1] College of Mechatronic Engineering, North University of China, Taiyuan, 030051, Shanxi
[2] Naval Research Academy, Beijing
[3] State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing
来源：
Baozha Yu Chongji/Explosion and Shock Waves | 2019年 / 39卷 / 01期
关键词：
Coated steel plate; Coating fracture; Cubic fragment; High-hardness polyurea; Penetration resistance;
D O I：
10.11883/bzycj-2018-0224
中图分类号：
学科分类号：
摘要：
In view of its differences from the conventional polyurea elastomer, we investigated the penetration resistance and fracture mechanism of coatings made from high-hardness polyurea sprayed on steel plates, using the ballistic experiment to obtain the ballistic limit of uncoated and coated steel plates subjected to 3.3 g cubic fragments, in consideration of polyurea coatings on the front side, the back side and on both sides in coated plates. We also analyzed the penetration resistance, fracture patterns and micro-morphologies of the coatings in different coated structures. The results indicate that the front coatings with severe fractures exhibited a high energy absorption capability, thereby improving the penetration resistance of the coated plates whereas, however, the back coatings that had been destroyed before the steel plates exhibited a lower energy absorption capability, which was bad for raising the penetration resistance. Under the fragment impact, polyurea coatings exhibited obvious velocity effects, thickness effects and micro-morphological characteristics, reflecting the differences of energy absorption in each configuration. © 2019, Editorial Staff of EXPLOSION AND SHOCK WAVES. All right reserved.
引用
收藏
相关论文
共 11 条
  • [1] Wang B., Liu P., Discussion on hot issues of polyurea, China Coatings, 24, 10, pp. 23-26, (2009)
  • [2] Zhao P., Zhang P., Zhang L., Et al., Experimental investigation on the performance of polyurea-coated structure under blast loads, Transactions of Beijing Institute of Technology, 38, 2, pp. 118-123, (2018)
  • [3] Feaga M.K., The effect of projectile strike velocity on the performance of polyurea coated RHA plates under ballistic impact, (2007)
  • [4] Mohotti D., Ngo T., Mendis P., Et al., Polyurea coated composite aluminium plates subjected to high velocity projectile impact, Materials and Design, 52, pp. 1-16, (2013)
  • [5] Mohotti D., Ngo T., Raman S.N., Et al., Plastic deformation of polyurea coated composite aluminium plates subjected to low velocity impact, Materials and Design, 56, pp. 696-713, (2014)
  • [6] Roland C.M., Fragiadakis D., Gamache R.M., Et al., Factors influencing the ballistic impact resistance of elastomer-coated metal substrates, Philosophical Magazine, 93, 5, pp. 468-477, (2013)
  • [7] Roland C.M., Fragiadakis D., Gamache R.M., Elastomer-steel laminate armor, Composite Structures, 92, 5, pp. 1059-1064, (2010)
  • [8] Bogoslovov R.B., Roland C.M., Gamache R.M., Impact-induced glass transition in elastomeric coatings, Applied Physics Letters, 90, 22, (2007)
  • [9] Gamache R.M., Giller C.B., Montella G., Et al., Elastomer-metal laminate armor, Materials and Design, 111, pp. 362-368, (2016)
  • [10] Giller C.B., Gamache R.M., Wahl K.J., Et al., Coating/substrate interaction in elastomer-steel bilayer armor, Journal of Composite Materials, 50, 20, pp. 2853-2859, (2016)
12