Prediction of creep performance for multiple launch rocket canister under long-term storage

被引：0
|
作者：
Sun T. [1 ]
Yu C. [1 ]
Qin Y. [1 ]
Wang Q. [2 ]
机构：
[1] School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing
[2] Jiangxi Changjiang Chemical Co., Ltd, Jiujiang
来源：
Guofang Keji Daxue Xuebao/Journal of National University of Defense Technology | 2020年 / 42卷 / 05期
关键词：
Composite director; Creep deformation; Finite-element analysis; Launch canister; Long-term storage; User-defined subroutine;
D O I：
10.11887/j.cn.202005009
中图分类号：
学科分类号：
摘要：
In order to investigate the creep performance of multi-barrel rocket weapon launch canister under long-term storage, uniaxial tensile creep test was carried out on composite laminate and the creep constitutive model parameters of single layer in the main directions were obtained. The finite element method and the user-defined material subroutine were used to establish long-term storage numerical analysis model of launch canister. Creep deformation of the bottom launch canister after 15 years storage was predicted. Taking the stored launch canister as initial state, the dynamic simulation model of rocket-tube coupling was built, and the influence of creep on rocket launching process was further investigated. Simulation results show that the change of the parallelism of the director and the flatness of the bottom surface of launch canister caused by creep are smaller than the specified values of technical indicators. The maximum residual deformation of director bundle is saddle-shaped in three-dimensional space, and the deformations of the middle position directors for upper and lower rows are largest, while that of the middle position directors for left and right columns are smallest. Creep deformation of the director reduces the clearance between rocket and director, increases the dynamic contact collision force and lessens the off-track velocity of rocket. © 2020, NUDT Press. All right reserved.
引用
收藏
页码：60 / 67
页数：7
相关论文
共 22 条
  • [1] YU Cungui, LI Zhigang, Analysis of rocket launching system, pp. 67-68, (2012)
  • [2] Liu C, Liu P, Zhao Z B, Et al., Room temperature creep of a high strength steel, Materials & Design, 22, 4, pp. 325-328, (2001)
  • [3] Becker A A, Hyde T H, Sun W, Et al., Benchmarks for finite element analysis of creep continuum damage mechanics, Computational Materials Science, 25, 1, pp. 34-41, (2002)
  • [4] Chen J N, Chen J J, Tu S D., Case study of strain based criterion for high temperature design, Pressure Vessel Pipe, 1, (2003)
  • [5] Colombo P P, Garzillo A, Meriggi M, Et al., Creep and damage analysis of a serviced tee intersection in a boiler header: comparison between numerical and experimental results, International Journal of Pressure Vessels and Piping, 66, 1, pp. 243-251, (1996)
  • [6] WANG Ke, LIU Zunchao, LIU Tong, Et al., Finite element analysis of high temperature creep of shell for shell and tube heat exchanger, Materials for Mechanical Engineering, 38, 4, pp. 87-90, (2014)
  • [7] REN Chao, CHEN Jianjun, PAN Hongliang, Prediction model for visco-elastic behavior of fiber reinforced composites, Acta Materiae Compositae Sinica, 29, 1, pp. 162-168, (2012)
  • [8] ZHANG Xiaoyu, HUANG Qianyu, CHEN Jianzhong, Et al., The visco-elastic model of PMC unidirectional plates, Journal of Huazhong University of Science and Technology (Nature Science Edition), 1, pp. 30-33, (2015)
  • [9] Luciano R, Barbero E J., Analytical expression for the relaxation moduli of linear visco-elastic composites with periodic microstructure, Journal of Applied Mechanics, 62, 3, pp. 786-793, (1995)
  • [10] Harris J S, Barbero E J., Prediction of creep properties of laminated composites from matrix creep data, Journal of Reinforced Plastics and Composites, 17, 4, pp. 361-379, (1998)
123