Remnant coal pillar stress distribution and cross-pillar roadway layout control technology in extra-thick coal seam

被引：0

作者：

Wang P. ^{[1
,2
]}

Wang Z. ^{[2
,3
]}

Luo F. ^{[1
]}

Su Y. ^{[4
]}

Li J. ^{[2
,3
]}

Wu C. ^{[2
,3
]}

Zhang Z. ^{[1
]}

机构：

[1] College of Mining and Geomatics Engineering, Hebei University of Engineering, Handan

[2] China and Russia Dynamics Research Center, China University of Mining and Technology-Beijing, Beijing

[3] School of Energy and Mining Engineering, China University of Mining and Technology-Beijing, Beijing

[4] China Coal International Engineering Design and Research Institute, Beijing

来源：

Meitan Kexue Jishu/Coal Science and Technology (Peking) | 2023年 / 51卷 / 12期

关键词：

across coal pillar; combined support; extra-thick coal seam; residual coal; slice mining; slip-lines field;

D O I：

10.13199/j.cnki.cst.2022-2092

中图分类号：

学科分类号：

摘要：

The paper aims to determine the reasonable layout and stability control scheme of the mining roadway under the influence of remnant coal pillars in the multi-slice longwall mining of the extra thick coal seam in Laogong Yingzi Coal Mine. Combining field monitoring, theoretical analysis and numerical simulation, the stress distribution characteristics of the remnant coal pillar and the coal in the lower slice are studied to compare and analyze the stress states of the surrounding rock of roadways at different locations, the roadway layout across the remnant coal pillar is proposed, and a mechanical model of the floor slip line field is established. The model takes the width of the stress increasing area as the width of the bar-shaped foundation, the roadway layout scheme of 4 m horizontal distance from the remnant coal pillar iss determined. Combining with the roadway layout characteristics, the active and passive combined support scheme of “Ibeam steel sets + cable bolts + shotcrete + shallow hole low-pressure grouting” is proposed. The results show that there is a double peak stress concentration both within the remnant coal pillar and the lower coal slice after mining on both sides of the upper slice. Inside the coal pillar is the vertical stress concentration zone, and at the edge of the coal pillar is the shear stress concentration zone. External spaced overlapped roadway is influenced both by vertical and shear stresses. The stress concentration of external spaced overlapped roadway is the highest followed by vertical overlapped roadway and increases with the increase of the outer staggered distance. The influence of the shear stress is more obvious for vertical overlapped roadway. The influence of the vertical stress and shear stress on the roadway layout across the remnant coal pillar is significantly reduced, and the peak value of the vertical stress stabilizes at 34.1 MPa. The peak shear stress stabilizes at 6.7 MPa, and the stress concentration is the lowest and decreases with the increase of the interval of the two roadways. Field application results show that the deformation of roadway surrounding rock across the remnant coal pillar is small, and there is no intensive pressure observed, which meets the requirements of safety production. © 2023 China Coal Society. All rights reserved.

引用

页码：232 / 242

页数：10

共 19 条

[1] ZHU Sitao, MA Yuzhen, JIANG Fuxing, Et al., Mechanism of rock burst in the bottom coal seam of super high seam with overall slippage and instability[J], Journal of Mining & Safety Engineering, 38, 1, (2021)
[2] GAO Jianliang, Hanghang CAI, Fangchao LU, Et al., Study on underlying coal seam stress distribution and failure characteristics in slicing mining of extra-thick coal seams[J], Coal Science and Technology, 49, 5, (2021)
[3] BATUGIN Adrian, WANG Zhiqiang, SU Zehua, Et al., Combin-ed support mechanism of rock bolts and anchor cables for adjacent roadways in the external staggered split-level panel layout, International Journal of Coal Science & Technology, (2021)
[4] 1, pp. 37-40, (1994)
[5] Guozhi LI, SUN Lijun, Instability mechanism and support technology of coal pillar roadway in slice mining[J], Coal Engineering, 52, 12, (2020)
[6] YANG Jianhui, CAI Meifeng, GUO Yanhua, Study on the technique of sparklet-inboard-type layout of gateroad in the bottom slicings[J], Chinese Journal of Rock Mechanics and Engineering, 21, 8, (2002)
[7] ZHAO Hongbao, LIU Yihong, CHENG Hui, Et al., Mechanism and prevention measures of asymmetric floor heave in mining roadway of Huipodi Coal Mine[J], Journal of Mining Science and Technology, 5, 6, (2020)
[8] ZHAO Hongbao, CHENG Hui, LI Jinyu, Et al., Study on asymmetric deformation mechanism of surrounding rock of roadway under the effect of isolated coal pillar[J], Chinese Journal of Rock Mechanics and Engineering, 39, (2020)
[9] LUO Feng, CAO Shugang, LI Guodong, Et al., Temporal-spatial variation characteristics of strain in coal seam floor during downward and layer-by-layer mining in ultra-distance coal seams[J], Journal of Mining & Safety Engineering, 35, 5, (2018)
[10] HAO Dengyun, WU Yongzheng, CHEN Haijun, Et al., Instability mechanism and prevention technology of roadway in close distance and extra thick coal seam under goaf[J], Journal of China Coal Society, 44, 9, (2019)

← 1 2 →