High temperature creep behavior of friction stir welding joints for CLAM steel

被引：0
|
作者：
Tian C. [1 ]
Yang X. [1 ]
Li S. [1 ]
Tang W. [1 ]
Li H. [1 ]
机构：
[1] Tianjin Key Laboratory of Advanced Joining Technology, Tianjin University, Tianjin
来源：
Hanjie Xuebao/Transactions of the China Welding Institution | 2021年 / 42卷 / 02期
关键词：
Creep performance; Friction stir welding; Life prediction; Low activation steel; Microstructure;
D O I：
10.12073/j.hjxb.20200811003
中图分类号：
学科分类号：
摘要：
The uniaxial creep tensile strength, fracture features and microstructures of friction stir welded joint with postweld heat treatment for CLAM steel have been investigated in the range of the creep applied stress from 180 MPa to 300 MPa at 823 K condition. It is found that the creep life of the FSW joints of CLAM steel increase from 1.5 h, 19.2 h and 883 h to above 6769 h respectively, when the creep stresses decrease from 300 MPa, 260 MPa and 220 MPa to 180 MPa. The inter critical heat affected zone is the weakest zone of creep rupture resistance for the FSW joint of CLAM steel, the joints mainly exhibit dislocation-controlled creep deformation mechanism and the transgranular ductile fracture mode. The microstructures of inter critical heat affected zone produce recovery and subgrain boundaries are formed in here during creep process, which result in the decrease of dislocation strengthening action; the coarser M23C6carbides is produced or the coarser Laves phase around the M23C6 carbides is formed, which result in the reduction of precipitation and solution strengthening action, these issues are the main reasons for the deterioration of the creep performance of FSW joints. The creep fracture strength of FSW joint is estimated to be 156 MPa in the condition of 1 × 105 h creep life according to the Monkman-Grant equation, which reaches 88 % of the strength of base metal. Copyright © 2021 Transactions of the China Welding Institution. All rights reserved.
引用
收藏
页码：38 / 45
页数：7
相关论文
共 19 条
  • [1] Huang Qunying, Li Chunjing, Liu Shaojun, Et al., R & D status of materials for test blanket modules in China, Nuclear Science and Engineering, 29, 3, pp. 260-265, (2009)
  • [2] Tan L, Katoh Y, Tavassoli A A F, Et al., Recent status and improvement of reduced-activation ferritic-martensitic steels for high-temperature service, Journal of Nuclear Materials, 479, pp. 515-523, (2016)
  • [3] Sklenicka V, Kucharova K, Svoboda M, Et al., Long-term creep behavior of 9%-12% Cr power plant steels, Master Character, 51, pp. 35-37, (2003)
  • [4] Jiang Zhizhong, Huang Jihua, Hu Jie, Et al., Microstructure and mechanical properties of laser welded joints of CLAM steel used for fusion reactor, Transactions of the China Welding Institution, 33, 2, pp. 5-8, (2012)
  • [5] Aubert P, Tavassoli F, Rieth M, Et al., Review of candidate welding processes of RAFM steels for ITER test blanket modules and DEMO, Journal of Nuclear Materials, 417, 1−3, pp. 43-50, (2011)
  • [6] Das C R, Albert S K, Sam S, Et al., Mechanical properties of 9Cr-1W reduced activation ferritic martensitic steel weldment prepared by electron beam welding process, Fusion Engineering & Design, 89, 11, pp. 2672-2678, (2014)
  • [7] Xu Le, Wen Jianfeng, Tu Shandong, Numerical simulations of creep damage and crack growth in P92 steel welded joints, Transactions of the China Welding Institution, 40, 8, pp. 80-88, (2019)
  • [8] Albert S K, Tabuchi M, Hongo H, Et al., Effect of welding process and groove angle on type IV cracking behavior of weld joints of a ferritic steel, Science & Technology of Welding & Joining, 10, 2, pp. 149-157, (2013)
  • [9] Wang J, Lu S, Dong W, Et al., Microstructural evolution and mechanical properties of heat affected zones for 9Cr2WVTa steels with different carbon contents, Materials & Design, 64, 12, pp. 550-558, (2014)
  • [10] Noh S, Ando M, Tanigawa H, Et al., Friction stir welding of F82H steel for fusion applications, Journal of Nuclear Materials, 478, pp. 1-6, (2016)
12