Microstructure and properties of CuFeCrAlNiTi high entropy alloy coating prepared by cold spray assisted in-situ synthesis

被引：0

作者：

Feng L. ^{[1
,2
]}

Hu Y.-X. ^{[1
]}

Li W.-S. ^{[1
,2
]}

Wang G.-P. ^{[1
]}

Wang J. ^{[1
]}

机构：

[1] School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou

[2] State Key Laboratory of Advanced Processing and Reuse of Non Ferrous Metals, Lanzhou

来源：

Surface Technology | 2021年 / 50卷 / 07期

基金：

中国博士后科学基金;

关键词：

Cold spraying; CuFeCrAlNiTi high entropy alloy coating; Electrochemistry; Friction; In-situ synthesis;

D O I：

10.16490/j.cnki.issn.1001-3660.2021.07.020

中图分类号：

学科分类号：

摘要：

In order to improve the surface properties of common metal materials, a new technology for preparing CuFeCrAlNiTi high entropy alloy coating with good properties was proposed. In this paper, Cu, Fe, Cr, Al, Ni and Ti are used as raw materials. After 2 hours of mechanical mixing, the mixed metal coating is prepared on the 45# steel matrix by low-pressure cold spraying technology. Then, the mixed metal coating is synthesized in-situ into CuFeCrAlNiTi high-entropy alloy coating by induction remelting technology. Scanning electron microscope (SEM), energy spectrum (EDS) and X-ray diffraction (XRD) were used to observe and analyze the microstructure and phase structure of the mixed metal coating and the in-situ synthesis CuFeCrAlNiTi high-entropy alloy coating, and the hardness, friction and corrosion resistance of the in-situ synthesis CuFeCrAlNiTi high-entropy alloy coating were analyzed. The results showed that CuFeCrAlNiTi high entropy alloy coating was prepared in situ with fine microstructure and uniform element dispersion. The coating structure is the simple solid solution structure BCC phase and FCC phase. The coating has a good comprehensive performance with a hardness up to 543.4HV, and the dry friction coefficient with Al2O3 is 0.428, which is 61.6% of the dry friction coefficient between 45# and Al2O3. Besides, the coating has a better chlorine-resistant performance than the matrix, and will not form corrosion derivatives in the coating after the electrochemical corrosion of 1 mol/L NaCl solution and 0.5 mol/L H2SO4 solution. Therefore, CuFeCrAlNiTi high-entropy alloy coating synthesized in situ by cold spraying has relatively high hardness, good friction and chloride corrosion resistance. © 2021, Chongqing Wujiu Periodicals Press. All rights reserved.

引用

页码：194 / 202

页数：8

共 26 条

[1] Takeuchi A., Inoue A., Classification of bulk metallic glasses by atomic size difference, heat of mixing and period of constituent elements and its application to characterization of the main alloying element[J], Materials Transactions, 46, 12, pp. 2817-2829, (2005)
[2] Pi J H., Pan Y., Zhang L., Et al., Microstructure and property of AlTiCrFeNiCu high-entropy alloy[J], Journal of Alloys & Compounds, 509, 18, (2011)
[3] Nong Zhi-Sheng W.A.N.G.H.-Y., Ji-Jie W.A.N.G., Et al., Relationship between composition and elastic properties of AlxCrFeNiTi based high entropy alloys[J], Acta Physica Sinica, 68, 3, pp. 212-221, (2019)
[4] Li Wei L.I.U., Gui-Zhong G.U.O., Jing-jie. Study on microstructure and electrochemical properties of AlxFeCoNiCrTi high entropy alloys[J], Casting, 58, 5, pp. 431-435, (2009)
[5] Si-Meng C.H.E.N.G., Study on microstructure and properties of CrFeCoNiTix high entropy Alloy prepared by powder metallurgy[D]. Harbin: Harbin University of, Science and Technology, (2019)
[6] Di G.A.O., High-Entropy Alloy Microstructure and Property Research[D], (2019)
[7] Lei H.U.A.N.G., Xue-Jie W.A.N.G., Chang-Zheng W.A.N.G., Et al., Effect of Ti on microstructure and friction properties of AlCoCrFeNiTix high entropy alloy[J], Special Casting & Nonferrous Alloy, 40, 5, pp. 562-566, (2020)
[8] Wang Tong Y.E.X.-C., Zhang-Yang X.U., Et al., Effect of Ti content on microstructure and mechanical properties of CuCoFeNi high-entropy alloys[J], International Journal of Minerals Metallurgy and Materials, 27, 10, (2020)
[9] Varalakshmi S., Kamaraj M., Murty B S., Synthesis and characterization of nanocrystalline AlFeTiCrZnCu high entropy solid solution by mechanical alloying[J], Journal of Alloys & Compounds, 460, 1-2, (2008)
[10] Zhao D., Yamaguchi T., Shu J., Et al., Rapid fabrication of the continuous AlFeCrCoNi high entropy alloy coating on aluminum alloy by resistance seam welding[J], Applied Surface Science, 145, (2020)

← 1 2 3 →