Simplified jacobian analysis for parallel robots with regular limbs

被引：0
|
作者：
Bu W. [1 ]
Zheng Y. [1 ]
Zhang P. [1 ]
Hua B. [1 ]
机构：
[1] School of Mechanical Engineering, Tongji University, Shanghai
来源：
Bu, Wanghui (buwanghui@tongji.edu.cn) | 1600年 / Chinese Mechanical Engineering Society卷 / 52期
关键词：
Actuating wrenches; Jacobian; Parallel manipulators; Screw theory; Twists;
D O I：
10.3901/JME.2016.09.036
中图分类号：
学科分类号：
摘要：
Jacobian is significant to the analysis of kinematics, precision and stiffness of parallel manipulators. Usually the wrench, which is reciprocal to all the twists in a limb except the twist of the actuated joint, is needed for Jacobian analysis. The procedure to calculate this wrench, however, is quite complex. Hence, for the particular limb structures commonly used in parallel robots, a novel concept about the regular limbs is presented, and the limb structural characteristics are summarized. The actuating wrenches of the revolute and prismatic joints are studied, and the approach to simplify the Jacobian analysis of parallel robots is proposed based on the actuating wrenches, which overcomes the complex procedure in existing methods to calculate the limb constraint wrench produced by the actuated joint. The partial Jacobian matrix can be obtained without the calculation of the limb constraint wrenches, and the overall Jacobian matrix can be derived with these limb constraint wrenches to perform the kinematic and static bijection between actuated joints and the moving platform. The proposed method can not only apply to the common 6 DOF parallel robots, but also apply to the lower mobility parallel robots with regular limbs. © 2016 Journal of Mechanical Engineering.
引用
收藏
页码：36 / 41
页数：5
相关论文
共 15 条
  • [1] Xiong Y., Ding H., Liu E., Robotics, (1993)
  • [2] Murray R.M., Li Z., Sastry S.S., A Mathematical Introduction of Robotic Manipulation, (1994)
  • [3] Bu W., Liu Z., Tan J., Et al., Detachment avoidance of joint elements of a robotic manipulator with clearances based on trajectory planning, Mechanism and Machine Theory, 45, pp. 925-940, (2010)
  • [4] Bu W., Liu Z., Tan J., Inverse displacement analysis of 6R robots with offset wrists based on decoupling degrees of freedom at the cutoff points, Journal of Mechanical Engineering, 46, 21, pp. 1-5, (2010)
  • [5] Li Y., Mei J., Liu S., Et al., Dynamic dimensional synthesis of a 4-DOF high-speed parallel manipulator, Journal of Mechanical Engineering, 50, 19, pp. 32-40, (2014)
  • [6] Ren Z., Wang Z., Sun L., Forward kinematics solution for parallel manipulators based on improved artificial bee colony algorithm, Journal of Mechanical Engineering, 49, 13, pp. 48-55, (2013)
  • [7] Joshi A.S., Tsai L., Jacobian analysis of limited-DOF parallel manipulators, ASME Journal of Mechanical Design, 124, 6, pp. 254-258, (2002)
  • [8] Huang Z., The kinematics and type synthesis of lower-mobility parallel robot manipulator, Proceedings of the 11th World Congress in Mechanism and Machine Science, pp. 65-76, (2004)
  • [9] Zhu S.J., Huang Z., Ding H.F., Forward/Reverse velocity and acceleration analysis for a class of lower-mobility parallel mechanisms, ASME Journal of Mechanical Design, 129, 4, pp. 390-396, (2007)
  • [10] Lu Y., Hu B., Unified solving Jacobian/Hessian matrices of some parallel manipulators with n SPS active legs and a passive constrained leg, ASME Journal of Mechanical Design, 129, 11, pp. 1161-1169, (2007)
12