The Research of Machining Mechanism of Carbon Fiber Reinforced Plastic

被引：11
|
作者：
Jia Z. [1 ]
Bi G. [1 ]
Wang F. [1 ]
Wang X. [1 ]
Zhang B. [1 ]
机构：
[1] Key Laboratory for Precision and Non-traditional Machining Technology of Ministry of Education, Dalian University of Technology, Dalian
来源：
Jia, Zhenyuan (jzyxy@dlut.edu.cn) | 2018年 / Chinese Mechanical Engineering Society卷 / 54期
关键词：
Carbon fiber reinforced plastic(CFRP); Damage suppression; Fiber deformation; Machining mechanism; Micro-mechanical model;
D O I：
10.3901/JME.2018.23.199
中图分类号：
学科分类号：
摘要：
Carbon fiber reinforced plastic (CFRP) consists of fiber, matrix, and interface at micro level. Meanwhile, it has laminated feature and shows heterogeneous anisotropy at macro level. The essence of the CFRP removal in machining is the complex process including simultaneous failure of the high-strength fiber and low-strength matrix under cutting force and heat, which results in machining damage easily. Analyzing the material removal process deeply is the key to reveal the machining mechanism of the CFRP, which can help to control the machining damage. The material removal process is mainly determined by the facture process of the fiber due to the fact that the fiber bears main load during the CFRP machining. Therefore, a micro-mechanical model of cutting a single fiber is proposed by analyzing the stress state of the fiber based on the two-parameter elastic foundations to describe the fiber fracture process exactly. In order to represent the stress state of the single fiber accurately, the model is considered the normal and shear effect on the fiber deformation, and the property change of the epoxy as well as interface with respect to temperature. The machining mechanism of the CFRP is revealed as follows: the depth of fiber deformation is influenced by the cutting depth and the fiber orientation. The depth of fiber deformation is increased with the increase of the cutting depth, which will result in machining damage more easily. And the depth of fiber deformation decreases with the increase of the fiber orientation. In order to verify the proposed model, the micro-mechanical model of cutting a single fiber is acquired to calculate the macroscopic cutting force. Then the model is validated indirectly through the comparing of the calculated value of macroscopic cutting force with the experimental value. And the calculation accuracy of the cutting force increases 20% on average because of considering the shear effect and the property change of the epoxy as well as interface with respect to temperature. In addition, the model can reveal the machining mechanism of the CFRP at micro level more accurately and provide theoretical basis for subsequent studies of the damage suppression. © 2018 Journal of Mechanical Engineering.
引用
收藏
页码：199 / 208
页数：9
相关论文
共 21 条
  • [1] Davim J.P., Machining of Composite Materials, (2010)
  • [2] Du S., Advanced composite materials and aerospace engineering, Acta Materiae Compositae Sinica, 24, 1, pp. 1-12, (2007)
  • [3] Soussia A.B., Mkaddem A., Mansori M.E., Rigorous treatment of dry cutting of FRP-Interface consumption concept: A review, International Journal of Mechanical Sciences, 83, pp. 1-29, (2014)
  • [4] Teti R., Machining of composite materials, CIRP Annals-Manufacturing Technology, 51, 2, pp. 611-634, (2002)
  • [5] Che D., Saxena I., Han P.D., Et al., Machining of carbon fiber reinforced plastics/polymers: a literature review, Journal of Manufacturing Science and Engineering, 136, 3, (2014)
  • [6] Wang C.Y., Liu G.Y., An Q.L., Et al., Occurrence and formation mechanism of surface cavity defects during orthogonal milling of CFRP laminates, Composites Part B, 109, pp. 10-22, (2017)
  • [7] Su Y.L., Jia Z.Y., Niu B., Et al., Size effect of depth of cut on chip formation mechanism in machining of CFRP, Composite Structures, 164, pp. 316-327, (2017)
  • [8] Xu W.X., Zhang L.C., On the mechanics and material removal mechanisms of vibration-assisted cutting of unidirectional fiber-reinforced polymer composites, International Journal of Machine Tools & Manufacture, 80-81, 5, pp. 1-10, (2014)
  • [9] Xu W.X., Zhang L.C., Mechanics of fiber deformation and fracture in vibration-assisted cutting of unidirectional fiber-reinforced polymer composites, International Journal of Machine Tools & Manufacture, 103, pp. 40-52, (2016)
  • [10] Qi Z.C., Zhang K.F., Cheng H., Et al., Microscopic mechanism based force prediction in orthogonal cutting of unidirectional CFRP, The International Journal of Advanced Manufacturing Technology, 79, 5-8, pp. 1209-1219, (2015)
123