Damage Characteristics of Two HMX-based Anti-overloaded Explosives under Shock Loading

被引：0
|
作者：
Jiang X.-B. [1 ]
Jin P.-G. [1 ]
Wang J.-L. [1 ]
Yang J. [1 ]
Wang X.-F. [1 ]
机构：
[1] Xi'an Modern Chemistry Research Institute, Xi'an
来源：
Wang, Xiao-Feng (wangxf_204@163.com) | 2017年 / Institute of Chemical Materials, China Academy of Engineering Physics卷 / 25期
关键词：
CT test; Damage characteristics; HMX-based anti-overloaded explosive; Shock damage; Shock wave sensitivity;
D O I：
10.11943/j.issn.1006-9941.2017.12.004
中图分类号：
学科分类号：
摘要：
Two kinds(casting moulding and pressed fitting) of HMX-based anti-overloaded explosives were chosen to study the damage characteristics and damage failure mechanisms of explosives under overloaded conditions by shock loading. The shock damage was conducted based on shock wave sensitivity test. The damage characteristics of samples before and after shock loading were studied by CT and the shock wave sensitivity was also tested after damage. Results of CT test show that no macro-damage appear in explosive by pressed fitting after the shock damage, while a cavity with length of 7-8 mm and diameter of 1-2 mm appears in cast explosive and is located at 7-8 mm away from one end of the witness board. After shock damage experiments, for cast explosive, above the position of 40 mm from the bottom surface, the explosive density decrease by 1%-5%, and for the pressed fitting explosive, above the position of 50 mm from the bottom surface, the explosive density increase by 1%-8%. The shock wave sensitivity of the both samples decreases after shock damage. The critical gap thicknesses of the cast explosive decreases from 25-27 mm before damaged to 13-15 mm after damaged, while for pressed fitting explosive, the thickness decrease from 38-40 mm to 30-32 mm. © 2017, Editorial Board of Chinese Journal of Energetic Materials. All right reserved.
引用
收藏
页码：991 / 996
页数：5
相关论文
共 19 条
  • [1] Liu C., Browning R., Fracture in PBX9501 at low rate, 12th Symposium(International) on Detonation, pp. 121-126, (2002)
  • [2] Sandusky H.W., Influence of fresh damage on the shock reactivity and sensitivity of several energetic materials, 10th Symposium(International) on Detonation, pp. 490-498, (1993)
  • [3] Field J.E., Parry M.A., Palmer S.J., Et al., Deformation and explosive properties HMX powers and polymer bonded explosive, 9th Symposium(International) on Detonation, pp. 886-896, (1989)
  • [4] Rae P.J., Goldrein H.T., Palmer S.J., Et al., Studies of the failure mechanisms of polymer-bonded explosive by high resolution more interferometry and environmental scanning electron microscopy, 11th Symposium(International) on Detonation, pp. 66-75, (1998)
  • [5] Chen P.-W., Ding Y.-S., Mechanical behaviour and deformation and failure mechanisms of polymer bonded explosives, Chinese Journal of Energetic Materials(Hanneng Cailiao), 8, 4, pp. 161-166, (2000)
  • [6] Zhou Z.-B., Study on macro/micromechanical properies, deformation and failure of polymer-bonded explosives, (2012)
  • [7] Sun P.-P., Wang X.-F., Nan H., Et al., Fracture feature of AP grains with different sizes within explosive substrate under drop hammer impact loading, Chinese Journal of Energetic Materials(Hanneng Cailiao), 23, 1, pp. 53-56, (2015)
  • [8] Tian Y., Zhang W.-B., Wen M.-P., Et al., Research on correlation of thermal shock damage of PBX JOB-9003, Chinese Journal of Energetic Materials(Hanneng Cailiao), 12, 3, pp. 174-177, (2004)
  • [9] Zhang W.-B., Tian Y., Wen M.-P., Et al., Experimental study on the thermal shock damage of explosive by ultrasonic testing, Chinese Journal of Energetic Materials(Hanneng Cailiao), 12, 2, pp. 85-88, (2004)
  • [10] Tian Y., Zhang W.-B., Hao Y., Et al., Thermal shock damage of explosive and its ultrasonic characterization, Chinese Journal of Explosives & Propellants, 23, 4, pp. 13-15, (2000)
12