Thermal stress analysis of high temperature pipe using cell-based smoothed point interpolation method (CS-PIM)

被引：1

作者：

Liu Y.-J. ^{[1
]}

Lu H. ^{[2
]}

Zhang G.-Y. ^{[1
,2
]}

Zong Z. ^{[1
,2
]}

机构：

[1] School of Naval Architecture Engineering, Dalian University of Technology, Dalian

[2] State Key Laboratory of Structural Analysis for Industrial Equipment, Dalian University of Technology, Dalian

来源：

Zhang, Gui-Yong (gyzhang@dlut.edu.cn) | 2016年 / Zhejiang University卷 / 50期

关键词：

High temperature pipes; Meshfree; Numerical method; Smoothed point interpolation method; Thermal stress;

D O I：

10.3785/j.issn.1008-973X.2016.11.011

中图分类号：

学科分类号：

摘要：

The cell-based smoothed point interpolation method (CS-PIM) was applied for thermoelastic problems in high temperature pipe system, for which a finite element method (FEM) model generally results in bad accuracy due to the natural overly-stiff property. In the scheme of CS-PIM, the computational domain was discretized into triangular/tetrahedron background cells, Then the generalized gradient smoothing operation was conducted upon the cells and shape functions were constructed using the point interpolation method. Both 2D and 3D cases study were conducted.The CS-PIM can obtain similar convergence rate but better accuracy for temperature results than the FEM does with the same mesh. For thermal stress analysis, the method achieves better results about both accuracy and convergence than the traditional FEM owing to the effectively softened stiffness. © 2016, Zhejiang University Press. All right reserved.

引用

页码：2113 / 2119

页数：6

共 18 条

[1] Deng Z.-W., Analysis on the operating conditions and material requirements of the pressure pipe, Pipeline Technique and Equipment, 4, pp. 18-20, (2009)
[2] Hong Z.H., Liu R., Liu W.B., Et al., A lateral global buckling failure envelope for a high temperature and high pressure (HT/HP) submarine pipeline, Applied Ocean Research, 51, pp. 117-128, (2015)
[3] Huang Y.-D., Selection and application for high temperature pipeline insulation materials, Energy for Metallurgical Industry, 32, 4, pp. 57-60, (2013)
[4] Zhang Z.-Q., Jiang X.-L., Analysis of the burst of boiler high-temperature superheater tubes, Mechanical & Electrical Engineering Technology, 44, 2, pp. 107-110, (2015)
[5] Yan W.-G., Yu X.-L., Lu G.-D., Et al., Heat transfer and pressure drop of heat pipe heat exchanger, Journal of Zhejiang University: Engineering Science, 45, 1, pp. 132-135, (2011)
[6] Zhang F., Liu Y.-M., Lou J., Stress and strain analysis and simulation of high temperature pressure pipe tee joint, Journal China University of Metrology, 22, 4, pp. 356-360, (2011)
[7] Chen X.-Y., Duan M.-L., Zeng X.-G., Et al., Numerical simulation research on upheaval buckling of high temperature submarine buried pipeline, The Ocean Engineering, 31, 5, pp. 103-111, (2013)
[8] Zhang Y.-L., Chong D.-T., Liu J.-P., Et al., Numerical investigation on conjugated heat transfer of conduction in wall and mixed convection, Xi'an Jiaotong University, 46, 5, (2012)
[9] Zienkiewicz O.C., Taylor R.L., The Finite Element Method (V1: The Basis), pp. 1-663, (2000)
[10] Liu W.K., Jun S., Zhang Y.F., Reproducing kernel particle methods, Int J Number Meth Eng, 20, 8-9, pp. 1081-1106, (1995)

← 1 2 →