Effect of Laser Energy Density on Microstructure and Properties of Laser Cladding NiCoCrAlY Coating

被引：0
|
作者：
Nie J. [1 ]
Yang Y. [1 ]
Li Y. [1 ]
Zhang H. [1 ]
Wei S. [1 ]
Cai J. [2 ]
Guan Q. [3 ]
机构：
[1] School of Materials Science and Engineering, North University of China, Taiyuan
[2] Institute of Advanced Manufacturing and Modern Equipment Technology, Jiangsu University, Zhenjiang
[3] School of Material Science and Engineering, Jiangsu University, Zhenjiang
来源：
Binggong Xuebao/Acta Armamentarii | 2021年 / 42卷 / 05期
关键词：
Hardness; Laser cladding; NiCoCrAlY coating; Wear resistance;
D O I：
10.3969/j.issn.1000-1093.2021.05.021
中图分类号：
学科分类号：
摘要：
NiCoCrAlY coating was prepared on the surface of 304 stainless steel in order to study the effect of energy density on the microstructure and properties of NiCoCrAlY coating during laser cladding. The phase composition and microstructure of NiCoCrAlY coating were analyzed by X-ray diffractometer (XRD) and scanning electron microscope (SEM). The hardness and wear resistance of NiCoCrAlY coating were studied by using a micro Vickers hardness tester and reciprocating friction and wear testing machine. The results show that the number of pores in NiCoCrAlY coating decreases with the increase in laser energy density, and the penetration and melting height increase with the increase in laser energy density. When the laser energy density is 3.8 kJ/cm2, the coating dilution rate is the lowest, and the number of pores is less. The NiCoCrAlY coating contains γ/γ' phase and β phase, and its microstructure is mainly columnar crystals. As the laser energy density increases, β phase content increases and the columnar crystals become larger. The hardness of NiCoCrAlY coating is higher than that of the substrate at different laser energy densities. The coating hardness is the highest when the laser energy density is 3.8 kJ/cm2, which is 301 HV0.2. In the reciprocating friction and wear experiment, when the laser energy density is 3.8 kJ/cm2, the friction coefficient is the smallest (0.46) and wear volume is the smallest (0.235 9 mm3), the wear mechanism is mainly abrasive wear, and the wear resistance is the best. © 2021, Editorial Board of Acta Armamentarii. All right reserved.
引用
收藏
页码：1083 / 1091
页数：8
相关论文
共 22 条
  • [1] TOLPYGO V K, CLARKE D R., On the rumpling mechanism in nickel-aluminide coatings: part Ⅰ: an experimental assessment, Acta Materialia, 52, 17, pp. 5115-5127, (2004)
  • [2] DU W., Study on the microstructure and high temperature oxidation resistance of arc ion plating MCrAlY coating, (2018)
  • [3] GURRAPPA I, SAMBASIVA RAO A., Thermal barrier coatings for enhanced efficiency of gas turbine engines, Surface and Coatings Technology, 201, 6, pp. 3016-3029, (2006)
  • [4] SCHULZ U, LEYENS C, FRITSCHER K, Et al., Some recent trends in research and technology of advanced thermal barrier coatings, Aerospace Science and Technology, 7, 1, pp. 73-80, (2003)
  • [5] JIA J, LIU S Y, MENG J S, Et al., MCrAlY coating modified by rare earth for high-end equipment parts, China Surface Engineering, 31, 5, pp. 54-62, (2018)
  • [6] HEJRANI E, SEBOLD D, NOWAK W J, Et al., Isothermal and cyclic oxidation behavior of free standing MCrAlY coatings manufactured by high-velocity atmospheric plasma spraying, Surface and Coatings Technology, 313, pp. 191-201, (2017)
  • [7] FEIZABADI A, SALEHI DOOLABI M, SADRNEZHAAD S K, Et al., Cyclic oxidation characteristics of HVOF thermal-sprayed NiCoCrAlY and CoNiCrAlY coatings at 1 000 ℃, Journal of Alloys and Compounds, 746, pp. 509-519, (2018)
  • [8] ZHANG B Y, YANG G J, LI C X, Et al., Non-parabolic isothermal oxidation kinetics of low pressure plasma sprayed MCrAlY bond coat, Applied Surface Science, 406, pp. 99-109, (2017)
  • [9] LI Y X, SU K Q, BAI P K, Et al., Microstructure and property characterization of Ti/TiBCN reinforced Ti based composite coatings fabricated by laser cladding with different scanning speed, Materials Characterization, 159, (2020)
  • [10] LI Y X, ZHANG P F, BAI P K, Et al., Microstructure and properties of Ti/TiBCN coating on 7075 aluminum alloy by laser cladding, Surface and Coatings Technology, 334, pp. 142-149, (2018)
123