Effect of Particle and Microstructure on Fatigue Crack Initiation and Growth Behavior of Cu/WCp Composites

被引：0
|
作者：
Zhang Y. [1 ]
Guo R. [1 ,2 ]
Xia H. [1 ,2 ]
Yan F. [1 ,2 ]
Wang S. [1 ]
Li Y. [1 ]
机构：
[1] Faculty of Civil Engineering and Mechanics, Kunming University of Science and Technology, Kunming
[2] Yunnan Province University Key Laboratory of Advanced Material Mechanics Behavior and the Micro Structure Design, Kunming University of Science and Technology, Kunming
来源：
Guo, Rongxin (guorx@kmust.edu.cn) | 1600年 / Cailiao Daobaoshe/ Materials Review卷 / 31期
关键词：
Crack growth rate; Cu/WCp; In-situ fatigue SEM; Microstructure; Particle interface debonding; Particle-reinforced composite;
D O I：
10.11896/j.issn.1005-023X.2017.018.018
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
By in-situ scanning electron microscopy, the fatigue crack initiation and propagation behaviors of Cu/WCp compo-sites produced by powder metallurgy was studied, and effects of particle and microstructure on fatigue crack initiation and early pro-pagation mechanism of composites was analyzed. The results show that fatigue micro cracks initiated at the interface between WCp particles and matrix, potential fatigue cracks tend to nucleate and grow along particles. At low stress intensity factor range, the fatigue crack has obvious "abnormal phenomenon" and occupied 71% of the whole life. The early growth of fatigue crack was strongly affected by the local microstructure and WCp particles of composite, and the scattering of small fatigue cracks growth rate was large. As the length of a small crack was more than 150 μm, the crack growth rate increased rapidly until the specimen was quickly broken. Crack deflection, crack branching and the plastic wake decelerated the fatigue crack growth rate, however particle debonding accele-rated the composite fatigue crack growth rate. From the results of numerical simulation, the particle interface debonding of the composite was found to significantly enlarge the fatigue crack growth driving force, which accelerated the fatigue crack growth rate. © 2017, Materials Review Magazine. All right reserved.
引用
收藏
页码：85 / 91
页数：6
相关论文
共 21 条
  • [1] Sun C., Shen R., Song M., Simulation of mechanical beha-viors of SiC reinforced Al matrix composites by finite element me-thod, Chinese J Nonferr Met, 22, 2, (2012)
  • [2] Chawla N., Ganesh V.V., Fatigue crack growth of SiC particle reinforced metal matrix composites, Int J Fatigue, 32, 5, (2010)
  • [3] Zou L., Fan J., Zuo T., Et al., High-cycle fatigue behavior of 15%SiCp/2009Al composite prepared by powder metallurgy process, Chinese J Nonferr Met, 20, 10, (2010)
  • [4] Miller K.J., The behaviour of short fatigue cracks and their initiation part II-A general summery, Fatigue Fract Eng Mater Struct, 10, 2, (1987)
  • [5] Jordon J.B., Bernard J.D., Newman J.C., Quantifying microstructural small fatigue crack growth in an aluminum alloy using a silicon-rubber replica method, Int J Fatigue, 36, 1, (2012)
  • [6] Kaynak C., Ankara A., Baker T.J., A comparison of short and long fatigue crack growth in steel, Int J Fatigue, 18, 1, (1996)
  • [7] Cappelli M.D., Carlson R.L., Kardomateas G.A., The transition between small and long fatigue crack behavior and its relation to microstructure, Int J Fatigue, 30, 8, (2008)
  • [8] Gall K., Biallas G., Maier H.J., Et al., Environmentally influenced microstructural small fatigue crack growth in cast magnesium, Mater Sci Eng A, 396, 1, (2005)
  • [9] Mcdowell D.L., An engineering model for propagation of small cracks in fatigue, Eng Fract Mech, 56, 3, (1997)
  • [10] Zhang L., Huang X., Wu X., Et al., In-situ experiment on early growth of small fatigue crack of nickel-based super alloy GHD4169, J Aerospace Power, 29, 4, (2014)
123