Effect of Surface Roughness on Wear Rate of Copper-Zinc Alloy under Lubricated Conditions

被引：0
|
作者：
Liu L. [1 ,4 ]
Yang C. [1 ,4 ]
Dienwiebel M. [2 ,3 ]
机构：
[1] School of Mechanical Engineering, Changzhou University, Changzhou, 213164, Jiangsu
[2] Karlsruhe Institute for Technology, Institute for Applied Materials, Kaiserstraße 12, Karlsruhe
[3] Fraunhofer Institute for Mechanics of Materials IWM, Wöhlerstraße 11, Freiburg
[4] Jiangsu Key Laboratory of Green Process Equipment, Changzhou University, Changzhou, 213164, Jiangsu
来源：
Liu, Lin (liulin@cczu.edu.cn) | 1600年 / Science Press卷 / 37期
基金：
中国国家自然科学基金; 中国博士后科学基金;
关键词：
Copper-zinc alloy; Surface roughness; Wear model; Wear rate;
D O I：
10.16078/j.tribology.2017.05.009
中图分类号：
学科分类号：
摘要：
In this study, we investigated the running-in behavior of brass (i.e. 64% copper and 36% Zinc) sliding against 100Cr6 under lubricated conditions on a tribometer based on in-situ holographic microscopy and radionuclide technique. The corresponding relationships between coefficient of friction, surface roughness and wear rate of brass was studied. On this basis, the wear model for surface roughness was established. Moreover, the wear model was evaluated by method of fitting goodness. In the beginning of experiment, the surface of CuZn36 revealed rough being accompanied by high wear rate. For the remainder of the test, wear-resistant layer was gradually formed in the near-surface region of the wear track. Meanwhile, surface roughness and wear rate decreased and tended to be stable. The fitting goodness of wear model was 90.23%, which means that the model can predict wear rate effectively under certain working conditions. © 2017, Science Press. All right reserved.
引用
收藏
页码：625 / 630
页数：5
相关论文
共 23 条
  • [1] Liu J., Liu C., Li F.B., Et al., Effect of Cu content on the antibacterial activity of titanium-copper sintered alloys, Materials Science and Engineering C, 35, pp. 392-400, (2014)
  • [2] Dianez M.J., Donoso E., Criado J.M., Et al., Study b y DSC HRTEM of the aging strengthening of Cu-Ni-Zn-Al alloys, Material & Design, 92, pp. 184-188, (2016)
  • [3] Wen S., Huang P., Principles of Tribology (Fourth Edition), (2012)
  • [4] Archard J.F., Contact and rubbing of flat surfaces, Journal of Applied Physics, 24, 8, pp. 981-988, (1953)
  • [5] Claudio R., Da Silva A., Pintaude G., Uncertainty analysis on the wear coefficient of Archard model, Tribology International, 41, 6, pp. 473-481, (2008)
  • [6] Hanief M., Wani M.F., Effect of surface roughness on wear rate during running-in of En31-steel: Model and experimental validation, Materials Letters, 176, pp. 91-93, (2016)
  • [7] Liu W., Xu J., Feng D., Et al., The research status and prospect of synthetic lubricating oils, Tribology, 33, 1, pp. 91-104, (2013)
  • [8] Yuan C.Q., Peng Z., Yan X.P., Et al., Surface roughness evolutions in sliding wear process, Wear, 265, 3-4, pp. 341-348, (2008)
  • [9] Korres S., Dienwiebel M., Design and construction of a novel tribometer with on-line topography and wear measurement, The Review of Scientific Instruments, 81, 6, (2010)
  • [10] Jiang X.Q., Blunt L., Stout K.J., Development of a lifting wavelet representation for surface characterization, Proceedings of the Royal Society A Mathematica Physical And Engineering Sciences, 456, 2001, pp. 2283-2313, (2000)
123