Numerical study on heat transfer mechanism of brush seal based on three-dimensional solid modeling

被引：0
|
作者：
Sun D. [1 ]
Li G. [1 ]
Ai Y. [1 ]
Liu Y. [2 ]
Zhan P. [2 ]
Xin Q. [2 ]
机构：
[1] Liaoning Key Lab of Advanced Test Technology for Aerospace Propulsion System, School of Aero-Engine, Shenyang Aerospace University, Shenyang
[2] Key Lab for Power Transmission of Aero Engine, Shenyang Engine Research Institute, Aero Engine Corporation of China, Shenyang
来源：
Hangkong Dongli Xuebao/Journal of Aerospace Power | 2019年 / 34卷 / 08期
关键词：
Brush seal; Friction heat; Heat transfer mechanism; Temperature distribution; Three-dimensional solid modeling;
D O I：
10.13224/j.cnki.jasp.2019.08.001
中图分类号：
学科分类号：
摘要：
A model for solving the heat transfer characteristics of brush seals based on three-dimensional solid modeling was established. The distribution characteristics of the flow field and temperature field of the brush seal were analyzed by verifying the accuracy of the numerical model. The influences of the pressure ratio, the rotational speed and the interference on the maximum temperature of the brush wire were studied. The heat transfer mechanism of the brush seal was revealed. The results showed that the end-discharge brush wire and the rotor face were mainly concentrated in the high temperature area of the bristle. The maximum temperature of the brush wire increased with the increase of the pressure ratio, rotational speed and interference, in which the interference had obvious influence on the maximum temperature. When the amount of interference increased from 0.1mm to 0.7mm, the maximum temperature increased 1.61 times; The main source of heat of the brush seal was generated by friction between the brush and the rotor surface, the heat transfer form of the brush seal included conduction heat and convection heat exchange. The friction heat flow entered the brush wire bundle and the rotating shaft through the heat conduction form. When the contact force between the brush wire and the rotor increased, the frictional heat flux increased, and the maximum temperature rose. The friction heat flowed through the heat transfer between fluid and solid transmission, and the main form of heat dissipation was the leakage of air taking away part of the heat. © 2019, Editorial Department of Journal of Aerospace Power. All right reserved.
引用
收藏
页码：1633 / 1643
页数：10
相关论文
共 21 条
  • [1] Li J., Yan X., Song L., Et al., A review of sealing technologies in turbomachinery, Thermal Turbine, 37, 3, pp. 141-148, (2008)
  • [2] Chai B., Fu X., Numerical simulation on flow and temperature distributions of brush seals, Lubrication Engineering, 41, 2, pp. 121-125, (2016)
  • [3] Qiu B., Li J., A review of flow and heat transfer, mechanical characteristics of brush seals, Thermal Turbine, 42, 3, pp. 141-149, (2013)
  • [4] Hendricks R.C., Schlumberger S., Braun M.J., Et al., A bulk flow model of a brush seal system, (1991)
  • [5] Demiroglu M., Tichy J.A., An investigation of heat generation characteristics of brush seals, (2007)
  • [6] Dogu Y., Aksit M.F., Brush seal temperature distribution analysis, Engineering for Gas Turbines and Power, 128, 3, pp. 599-609, (2006)
  • [7] Li L., Wang Z., Song F., Et al., Numerical investigation of temperature field in brush seals, Journal of Aerospace Power, 25, 5, pp. 1018-1024, (2010)
  • [8] Ding S., Tao Z., Xu G., Numerical simulation on fluid flow and heat transfer of a brush seal configuration, Journal of Propulsion Technology, 20, 1, pp. 65-67, (1999)
  • [9] Qiu B., Li J., Investigation on the heat transfer characteristics of brush seals, Journal of Xi'an Jiaotong University, 45, 9, pp. 94-100, (2011)
  • [10] Qiu B., Li J., Chen C., Et al., Investigations on the heat transfer characteristics of brush seals based on computational fluid dynamics and finite element analysis, Journal of Engineering Thermophysics, 33, 12, pp. 2067-2071, (2012)
123