EXPERIMENTAL STUDY AND NUMERICAL SIMULATION OF SEISMIC PERFORMANCE OF STIFFENED THIN STEEL PLATE SHEAR WALLS CONSIDERING THE EFFECT OF VERTICAL LOAD ON FRAME COLUMN

被引：0
|
作者：
Fu B. [1 ]
Hong Q. [2 ]
Jing T. [1 ]
Sun H. [1 ]
Tong G.-S. [3 ]
机构：
[1] Hangzhou TONGMSK Architectural Structure Design Office Co., Ltd., Zhejiang, Hangzhou
[2] Beihui Green Construction Group Co., Ltd., Shandong, Heze
[3] Institute of High-Performance Structures and Materials, Zhejiang University, Zhejiang, Hangzhou
来源：
Gongcheng Lixue/Engineering Mechanics | 2023年 / 40卷 / 12期
关键词：
ductility; initial imperfection; shear resistance; stiffened thin steel plate shear wall; vertical load;
D O I：
10.6052/j.issn.1000-4750.2022.02.0146
中图分类号：
学科分类号：
摘要：
An experimental research was conducted on seismic behavior of stiffened thin steel plate shear walls (SPSWs) considering the effect of vertical load on frame column. Two full-scale rectangular concrete-filled steel tube columns-stiffened thin steel plate shear specimens were tested under low-cycle reverse load. The design of specimens considers two cases of vertical stiffeners with equal spacing and variable spacing. The test results show that the specimens have good ductility and energy consumption capacity when the frame columns are subjected to high axial pressure. The ultimate drift angle of the specimens reaches 1/30. The plastic deformation of the specimens is mainly manifested as the out-of-plane buckling, which satisfies the design concept of “strong column and weak beam”. The arrangement of the stiffeners has no obvious influence on the seismic performance of the specimens. The nonlinear finite element method is further used to study the influence of initial defects and axial compression ratio on the lateral resistance performance of the specimen. The analysis results show that the initial defect distribution mode of the wall and the out-of-plane deflection amplitude have little effect on the pushover curve of the specimens. When the axial compression ratio of the frame column is greater than 0.7, the bearing capacity and deformation capacity of the specimens are reduced. Based on the shear control failure characteristics of the specimens, the calculation method of the specimen’s shear capacity is given. The calculated value is in good agreement with the finite element simulation value, and it is conservative than the experimental value. © 2023 Tsinghua University. All rights reserved.
引用
收藏
页码：75 / 88
页数：13
相关论文
共 33 条
  • [1] ZHOU Yaobin, WU Fangzhong, FU Bo, Et al., Comparative analysis of high-rise steel structure residence in meizoseismal area based on seismic design codes of China, US and Europe, Building Structure, 51, pp. 789-793, (2021)
  • [2] FU Bo, Li Zijie, LIN Chenghao, Et al., Experimental research on seismic performance of steel plate shear wall with outer decorative layer considering the effect of vertical load, Industrial Construction, 52, 11, pp. 49-56, (2022)
  • [3] FU Bo, CHEN Yuan, SHENG Kai, Et al., A study on seismic behavior of full height opening stiffened thin steel plate shear wall, Journal of Vibration and Shock, 42, 12, pp. 18-28, (2023)
  • [4] AISC 341-05, Seismic provisions for structural steel buildings, (2005)
  • [5] FEMA 450, NEHRP recommended provisions for seismic regulations for new buildings and other structures, (2003)
  • [6] CAN/CSA S16-94, Limit states design of steel structures, (2001)
  • [7] LAN Tao, GUO Yanlin, HAO Jiping, Effects on structural behavior of steel plane shear wall(SPSW) with opening considering axial compression of the column during construction, Construction Technology, 40, 11, pp. 66-70, (2011)
  • [8] ZHANG X Q, GUO Y L., Behavior of steel plate shear walls with pre-compression from adjacent frame columns [J], Thin-Walled Structures, 77, pp. 17-25, (2014)
  • [9] PARK H G, KWACK J H, JEON S W, Et al., Frame steel plate wall behavior under cyclic lateral loading, Journal of Structural Engineering, 133, 3, pp. 378-388, (2007)
  • [10] CHOI I R, PARK H G., Hysteresis model of thin infill plate for cyclic nonlinear analysis of steel plate shear walls, Journal of Structural Engineering, 136, 11, pp. 1423-1434, (2010)
1234