Vibration reliability of mid-infrared solid laser

被引：0
|
作者：
Liu W. [1 ]
Su W. [2 ,3 ]
Luo W. [2 ,3 ]
Li J. [3 ]
Liu R. [2 ,3 ]
机构：
[1] School of Mechanics & Safety Engineering, Zhengzhou University, Zhengzhou
[2] MOE Key Lab of Disaster Forecast and Control in Engineering, Jinan University, Guangzhou
[3] Science and Technology on Reliability Physics and Application Technology of Electronic Component Laboratory, China Electronic Product Reliability and Environmental Testing Research Institute, Guangzhou
来源：
Hongwai yu Jiguang Gongcheng/Infrared and Laser Engineering | 2021年 / 50卷 / 04期
关键词：
Mid-infrared solid laser; Non-contact vibration measurement technique; Optical crystal assembly; Simulation; Vibration reliability;
D O I：
10.3788/IRLA20200242
中图分类号：
学科分类号：
摘要：
Based on ANSYS, finite element simulation calculation model of mid-infrared solid laser was established, and modal parameters, such as natural frequency and vibration mode were gained through modal analysis. Combined with non-contact vibration measurement technology, the vibration modal test platform was set up, and the reliability of the modal simulation model was verified by the comparison with the test. Then, on the basis of modal simulation, the vibration characteristics of laser optical crystal assembly was studied emphasisly under condition of sinusoidal frequency sweeping vibration of vehicle through response analysis, and equivalent stress, total mechanical strain, relation between displacement and excitation frequency can also be obtained. Last, the key positions that affecting the vibration reliability of laser were analyzed and the results provide useful reference for improving design. The results indicate that there are four natural frequencies and modes in middle infrared solid laser using bottom fixed constraint, within 2 000 Hz and the experimental results of the modal agree with simulation results, and the natural frequency error is less than 8%. The maximum total mechanical strain and equivalent stress appeared at the edge of the input mirror under the condition of vehicle frequency sweeping vibration. The axial displacement along the optical crystal assembly is the largest and its value is about 0.14 mm. Copyright ©2021 Infrared and Laser Engineering. All rights reserved.
引用
收藏
相关论文
共 15 条
  • [1] Gong Shuang, Tian Jinrong, Li Kexuan, Et al., Advances in new two-dimensional materials and its application in solid-state lasers, Chinese Optics, 11, 1, pp. 18-30, (2018)
  • [2] Wen Ya, Wu Chunting, Yuan Zerui, Et al., Research progress of far-infrared solid-state lasers, Chinese Optics, 11, 6, pp. 889-900, (2018)
  • [3] Qiu Bocang, Martin Hai Hu Martin Hai Hu, Wang Weimin, Et al., Design and fabrication of 12 W high power and high reliability 915 nm semiconductor lasers, Chinese Optics, 11, 4, pp. 590-603, (2018)
  • [4] Su Yuhui, Gong Xiaoxia, Lei Shengqiong, Et al., Discussion of reliability evaluation on infrared photovoltaic detector by noise, Infrared Technology, 31, 9, pp. 509-512, (2009)
  • [5] Rogalski A., Material considerations for third generation infrared photon detectors, Infrared Physics and Technology, 50, 2-3, pp. 53-58, (2007)
  • [6] Tobin Stephen P, Thermal cycling induced changes in excess dark current in very long wavelength HgCdTe photodiodes at low temperature, Journal of Electronic Materials, 35, pp. 1411-1415, (2006)
  • [7] Nie Zhiqiang, Wang Mingpei, Sun Yubo, Et al., High power semiconductor laser lifetime prediction and failure analysis based on Weibull and Log-normal distribution, Infrared and Laser Engineering, 48, S1, (2019)
  • [8] Peng Bo, Zhang Pu, Chen Tianqi, Et al., Reliability of bonding interface in high power diode lasers, Infrared and Laser Engineering, 47, 11, (2018)
  • [9] Hao Lichao, Huang Aibo, Lai Canxiong, Et al., Discussion of reliability analysis on IRFPAs by bad pixel, Infrared and Laser Engineering, 45, 5, (2016)
  • [10] Yuan Ligang, Zhou Shouhuan, Zhao Hong, Et al., 109.5 W output 1.94 micron Tm: YAP solid-state laser, Infrared and Laser Engineering, 48, 4, (2019)
12