Fatigue life estimation of additive manufactured parts in the as-built surface condition

被引：20
|
作者：
Pegues J.W. [1 ,2 ]
Shamsaei N. [1 ,2 ]
Roach M.D. [3 ]
Williamson R.S. [3 ]
机构：
[1] Department of Mechanical Engineering, Auburn University, Auburn, AL
[2] National Center for Additive Manufacturing Excellence (NCAME), Auburn University, Auburn, AL
[3] Department of Biomedical Materials Science, University of Mississippi Medical Center, Jackson, MS
来源：
Material Design and Processing Communications | 2019年 / 1卷 / 03期
关键词：
fatigue endurance limit; fatigue strength; laser powder bed fusion; surface roughness; titanium;
D O I：
10.1002/mdp2.36
中图分类号：
学科分类号：
摘要：
In this study, a simple approach for estimating the effect of surface roughness on the fatigue strength of additive manufactured Ti-6Al-4V is investigated. Surface roughness parameters are used to estimate the elastic stress concentration factor and the resulting fatigue stress concentration factor. The estimated fatigue strengths are then compared with experimentally obtained fatigue strengths for specimen batches with varying surface conditions. Results show that the estimated fatigue strengths are comparable with the experimental fatigue strengths, and the predicted stress-life curves fit the experimental data reasonably well. © 2019 John Wiley & Sons, Ltd.
引用
收藏
相关论文
共 50 条
  • [1] Surface parameters of as-built additive manufactured metal for intraosseous dental implants
    Dos Santos, Lara Caroline Pereira
    Malheiros, Fernando Costa
    Guarato, Alexandre Zuquete
    JOURNAL OF PROSTHETIC DENTISTRY, 2020, 124 (02): : 217 - 222
  • [2] Influence of defects and as-built surface roughness on fatigue properties of additively manufactured Alloy 718
    Balachandramurthi, Arun Ramanathan
    Moverare, Johan
    Dixit, Nikhil
    Pederson, Robert
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2018, 735 : 463 - 474
  • [3] As-built surface quality and fatigue resistance of Inconel 718 obtained by additive manufacturing
    Uriati F.
    Nicoletto G.
    Lutey A.H.A.
    Material Design and Processing Communications, 2021, 3 (04):
  • [4] Fatigue Properties of Powder Bed Fused Inconel 718 in As-Built Surface Condition
    Sprengel, M.
    Baca, A.
    Gumpinger, J.
    Connolley, T.
    Brandao, A.
    Rohr, T.
    Ghidini, T.
    MECHANICAL FATIGUE OF METALS: EXPERIMENTAL AND SIMULATION PERSPECTIVES, 2019, 7 : 91 - 97
  • [5] Fatigue behaviour of notched additive manufactured Ti6Al4V with as-built surfaces
    Kahlin, M.
    Ansell, H.
    Moverare, J. J.
    INTERNATIONAL JOURNAL OF FATIGUE, 2017, 101 : 51 - 60
  • [6] Thermometric investigations for the characterization of fatigue crack initiation and propagation in Wire and Arc Additively Manufactured parts with as-built surfaces
    Bercelli, Lorenzo
    Doudard, Cedric
    Calloch, Sylvain
    Le Saux, Vincent
    Beaudet, Julien
    FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES, 2023, 46 (01) : 153 - 170
  • [7] Fatigue properties of EBM as-built and chemically etched thin parts
    Persenot, Theo
    Buffiere, Jean-Yves
    Maire, Eric
    Dendievel, Remy
    Martin, Guilhem
    3RD INTERNATIONAL SYMPOSIUM ON FATIGUE DESIGN AND MATERIAL DEFECTS (FDMD 2017), 2017, 7 : 158 - 165
  • [8] Fatigue performance of additive manufactured metallic parts
    Spierings, A. B.
    Starr, T. L.
    Wegener, K.
    RAPID PROTOTYPING JOURNAL, 2013, 19 (02) : 88 - 94
  • [9] Surface treatment impact on fatigue life at 550 °C of the as-built Inconel 718 manufactured by laser-powder bed fusion
    Bianchetti, C.
    Tsoutsouva, M. G.
    Toualbi, L.
    Kanoute, P.
    MATERIALS CHARACTERIZATION, 2023, 206
  • [10] STUDY THE MICROHARDNESS AND SURFACE ROUGHNESS OF AS-BUILT AND HEAT-TREATED ADDITIVE MANUFACTURED IN718 ALLOY
    Maurya, Ajay Kumar
    Kumar, Amit
    UPB Scientific Bulletin, Series D: Mechanical Engineering, 2022, 84 (01): : 211 - 224
12345