Microstructure and mechanical properties of bimetallic intertexture structure fabricated by plasma arc additive manufacturing

被引：0

作者：

Guo S. ^{[1
]}

Wang P. ^{[1
]}

Zhou Q. ^{[1
]}

Zhu J. ^{[2
]}

Gu J. ^{[1
]}

机构：

[1] Key Laboratory of Controlled Arc Intelligent Additive Manufacturing Technology, Ministry of Industry and Information Technology, Nanjing University of Science & Technology, Nanjing

[2] Nanjing Institute of Technology, Nanjing

来源：

Hanjie Xuebao/Transactions of the China Welding Institution | 2021年 / 42卷 / 03期

关键词：

18Ni high strength steel; Additive manufacturing; High nitrogen austenitic stainless steel; Mechanical property; Microstructure;

D O I：

10.12073/j.hjxb.20201125004

中图分类号：

学科分类号：

摘要：

Using 18Ni high strength steel and high nitrogen austenitic stainless steel as wires, bimetallic intertexture structure of high strength steel and high nitrogen steel was fabricated by plasma arc additive manufacturing. The microstructure and mechanical properties of bimetallic intertexture structure of high strength steel and high nitrogen steel were studied by microstructure observation, microhardness and tensile strength test. The results indicate that the microstructure in high nitrogen steel region are mainly equiaxed crystals and dendrite of austenite, the microstructure of high strength steel area is lath martensite. The hardness of the high strength steel area varies from 480 to 500 HV, the hardness of high nitrogen steel area varies from 310 to 320 HV. The tensile test results show that the average tensile strength of the intertexture structure in the x direction is 1 092 MPa, which is slightly less than the tensile strength in the y direction of 1 189 MPa. The average elongation after fracture in the x direction is 20.0%, which is not much different from the elongation after fracture in the y direction which is 19.5%. The fracture presents dark gray and obviously fibrous, with a large number of equiaxed dimples distributed, the dimples are large and deep, and there is an obvious shear lip area on the edge of the fracture, which is a ductile fracture. Copyright © 2021 Transactions of the China Welding Institution. All rights reserved.

引用

页码：14 / 19

页数：5

共 12 条

[1] Yang Dongqing, Xiong Hanying, Hunag Yong, Et al., Microstructure and properties of ultra-high strength steel joints welded with high nitrogen austenite wire, Transactions of the China Welding Institution, 41, 12, pp. 44-48, (2020)
[2] Rajkumar V, Arivazhagan N., Role of pulsed current on metallurgical and mechanical properties of dissimilar metal gas tungsten arc welding of maraging steel to low alloy steel, Materials and Design, 63, pp. 69-82, (2014)
[3] Ming Zhu, Wang Kehong, Wang Wei, Et al., Effects of nitrogen content and welding current on microstructure and properties of the weld of high nitrogen austenite steel, Transactions of the China Welding Institution, 40, 1, pp. 104-108, (2019)
[4] Korobeinikov I, Perminov A, Heller H P, Et al., Inert gas atomization of high-nitrogen TRIP-steels, Advanced Engineering Materials, 21, 5, pp. 89-97, (2019)
[5] Zhang Xiaoyong, Zhou Qi, Wang Kehong, Et al., Study on microstructure and tensile properties of high nitrogen Cr-Mn steel processed by CMT wire and arc additive manufacturing, Materials and Design, 166, pp. 1-15, (2019)
[6] Li Dongjie, Lu Shanping, Li Dianzhong, Et al., Research on microstructure and impact performance of high nitrogen steel weld, Acta Metallurgica Sinica, 49, 2, pp. 129-136, (2013)
[7] Sun Qingjie, Sang Haibo, Liu Yibo, Et al., Cross section scan trace planning based on arc additive manufacturing, China Welding, 28, 4, pp. 16-21, (2019)
[8] Cunningham C R, Flynn J M, Shokrani A, Et al., Strategies and processes for high quality wire arc additive manufacturing, Additive Manufacturing, 22, pp. 672-686, (2018)
[9] Hoefer K, Mayr P., 3DPMD-arc-based additive manufacturing with titanium powder as raw material, China Welding, 28, 1, pp. 11-15, (2019)
[10] Liu Dongyu, Li Dong, Li Kaibin, Et al., Microstructure and properties of welded joint of E36 steel and 304 stainless steel by electron beam welding, Aeronautical Manufacturing Technology, 6, pp. 29-33, (2014)

← 1 2 →