Research on Additive Manufacturing Technology and Equipment for Fiber Reinforced Resin Composites

被引：6
|
作者：
Shan Z. [1 ]
Fan C. [1 ]
Sun Q. [1 ]
Zhan L. [1 ]
机构：
[1] State Key Laboratory of Advanced Forming Technology and Equipment, China Academy of Machinery Science and Technology Group Co., Ltd., Beijing
来源：
Zhongguo Jixie Gongcheng/China Mechanical Engineering | 2020年 / 31卷 / 02期
关键词：
Additive manufacturing; Continuous fiber composite; Fiber reinforcement; Thermoplastic resin;
D O I：
10.3969/j.issn.1004-132X.2020.02.007
中图分类号：
学科分类号：
摘要：
Based on the review of the research status of fiber reinforced resin composites at home and abroad, the forming methods, processes and properties of short fiber, long fiber and continuous fiber reinforced resin composites were analyzed. In view of the additive manufacturing forming of high performance continuous fiber reinforced resin composites, the additive manufacturing forming mechanism and processes of continuous fiber were studied, the influence rules of forming performance were revealed. The future development trends of additive manufacturing technology and equipment for fiber reinforced resin composites were pointed out, it was urgent to carry out the research on additive manufacturing forming mechanism, forming processes and equipment for fiber reinforced resin composites, so as to better promote the wide applications. © 2020, China Mechanical Engineering Magazine Office. All right reserved.
引用
下载
收藏
页码：221 / 226
页数：5
相关论文
共 28 条
  • [1] Li B., Xing L., Bao J., Et al., Research and Development Progress of National Key Laboratory of Advanced Composites on Advanced Aeronautical Resin Matrix Composites, Journal of Aeronautical Materials, 36, 3, pp. 92-100, (2016)
  • [2] Wang X., Yu Y., Li S., Et al., The Research on Fiber Reinforced Thermoplastic Composites, Fiber Composite, 2, pp. 44-47, (2011)
  • [3] Kang H., Shan Z., Zang Y., Et al., Effect of Yarn Distortion on the Mechanical Properties of Fiber-bar Composites Reinforced by Three-dimensional Weaving, Applied Composite Materials, 23, 2, pp. 119-138, (2016)
  • [4] Wu X., Shan Z., Liu F., Et al., Research on Surface Structures of Guide Sleeves for 3D Woven Composites, Materials Reports, 28, 22, pp. 1-4, (2014)
  • [5] Wu Y., Review and Prospect of Development on Aerospace Composite Technology, Technology Innovation and Application, 17, (2015)
  • [6] Sugavaneswaran M., Arumaikkannu G., Modelling for Randomly Oriented Multi Material Additive Manufacturing Component and Its Fabrication, Materials & Design, 54, pp. 779-785, (2014)
  • [7] Gurr M., Hofmann D., Ehm M., Et al., Acrylic Nanocomposite Resins for Use in Stereolithography and Structural Light Modulation Based Rapid Prototyping and Rapid Manufacturing Technologies, Advanced Functional Materials, 18, 16, pp. 2390-2397, (2008)
  • [8] Griffini G., Invernizzi M., Levi M., Et al., 3D-printable CFR Polymer Composites with Dual-cure Sequential IPNs, Polymer, 91, pp. 174-179, (2016)
  • [9] Salazar A., Rico A., Rodriguez J., Et al., Fatigue Crack Growth of SLS Polyamide 12: Effect of Reinforcement and Temperature, Composites, Part B: Engineering, 59, pp. 285-292, (2014)
  • [10] Floersheim R.B., Hou G., Firestone K., CFPC Material Characteristics and SLS Prototyping Process, Rapid Prototyping Journal, 15, 5, pp. 339-345, (2009)
123