Decoupling on Influence of Air Droplets Stress and Canopy Porosity Change on Deposition Performance in Air-assisted Spray

被引：0
|
作者：
Liu X. [1 ,2 ]
Song L. [1 ]
Cui H. [1 ]
Liu Y. [1 ]
Liu X. [1 ,2 ]
Wu M. [1 ]
机构：
[1] School of Mechanical and Electronic Engineering, Shandong Agricultural University, Tai'an
[2] Shandong Agricultural Equipment Intelligent Engineering Laboratory, Tai'an
[3] Shandong Provincial Key Laboratory of Horticultural Machinery and Equipment, Tai'an
来源：
Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery | 2021年 / 52卷 / 08期
关键词：
Air-assisted spraying; Airflow droplets stress; Canopy porosity change; Decoupling; Droplets deposition;
D O I：
10.6041/j.issn.1000-1298.2021.08.011
中图分类号：
学科分类号：
摘要：
In the air-assisted spray, the change in the porosity of the canopy caused by the wind speed of the auxiliary airflow and the effect on the droplet migration were coupled, and the two ultimately affected the droplet deposition performance. Studying the effect of the coupling ratio of the two on the deposition performance can provide guidance for the optimization of air-assisted spray parameters and the improvement of spray patterns. Taking cotton in the full blooming period as the research object, and the different effects of the decoupling of the two on the droplet deposition behavior were analyzed by designing a decoupling test plan. Firstly, the deformation of cotton branches and leaves under wind load was calibrated with the help of a high-speed camera, and the fitting relationship among air velocity, leaf area and deformation was obtained. Through carrying out the wind load deformation test of the fake blade, it was verified that the wind load deformation error of the fake blade and the real blade was basically less than 17%. The plan of using the simulated cotton model to be applied to the air-assisted spray test was determined. Then, according to the 3/8 rule of the branch and leaf configuration of cotton growth and development, a cotton model of Scheme 1 in which the canopy porosity can be changed by wind load was built. The data of the airflow field in the cotton canopy was measured, and the deformation of branches and leaves under different wind speeds was calculated. Physical means were used to fix the deformation of branches and leaves, and a Scheme 2 cotton model was formed with fixed canopy porosity after wind load deformation. The cotton branches and leaves was fixed in the natural state and the canopy porosity was kept unchanged under wind load as the cotton model of Scheme 3. Finally, for the cotton models of the three test schemes, the auxiliary air flow velocity was changed to carry out air-assisted droplet deposition experiments. The test results showed that the migration effect of airflow on droplets was more favorable to the deposition behavior of droplets in the canopy than changes in canopy porosity. The effect of air flow on the movement of droplets increased the droplet deposition rate by 39.81%, and the change in canopy porosity increased the droplet deposition rate by 10.52%. The droplet transport channel formed by the increase of canopy pores was more conducive to the uniform distribution of droplets in the canopy than the transport effect of airflow on the droplets. The increase in the porosity of the canopy increased the deposition uniformity by 42.71%, and the transport effect of the air flow on the droplets increased the deposition uniformity by 1.10%. This decoupling method can provide a reference for the design of spray patterns for different crop canopy porosity changes. © 2021, Chinese Society of Agricultural Machinery. All right reserved.
引用
下载
收藏
页码：117 / 126and137
相关论文
共 27 条
  • [1] YANG Fengbo, ZHANG Ling, XUE Xinyu, Et al., Numerical simulation and test of wind performance of gas spray nozzle for orchard air-assisted sprayer, Transactions of the Chinese Society for Agricultural Machinery, 49, 6, pp. 38-47, (2018)
  • [2] WANG Ning, ZHAI Changyuan, ZHAO Chunjiang, WANG Ning, Et al., Research progress on precision control methods of air-assisted spraying in orchards, Transactions of the CSAE, 34, 10, pp. 1-15, (2018)
  • [3] LIU Xuemei, ZHANG Xiaohui, HOU Cunliang, Air flow simulation and flow field optimization for airduct of air-assisted boom sprayer, Transactions of the Chinese Society for Agricultural Machinery, 42, 4, pp. 70-75, (2011)
  • [4] CUI Longfei, XUE Xinyu, QIN Weicai, Parameter optimization on crop divider of cotton defoliation sprayer based on EBFNN, Transactions of the Chinese Society for Agricultural Machinery, 47, 5, pp. 62-69, (2016)
  • [5] WEI Xinhua, SHAO Jing, XIE Luguan, Et al., Design and experiment of air-assisted cotton boom sprayer with separating row and spraying in inside and upper canopy, Transactions of the Chinese Society for Agricultural Machinery, 47, 1, pp. 101-107, (2016)
  • [6] LI Longlong, HE Xiongkui, SONG Jianli, Et al., Design and experiment of automatic profiling orchard sprayer based on variable air volume and flow rate, Transactions of the CSAE, 33, 1, pp. 70-76, (2017)
  • [7] SINHA R, RANJAN R, KHOT L R, Et al., Comparison of within canopy deposition for a solid set canopy delivery system (SSCDS) and an axial-fan airblast sprayer in a vineyard, Crop Protection, 132, (2020)
  • [8] SUN Chengda, LIU Changding, Construction and application of droplet canopy penetration model for air-assisted spraying pattern, Transactions of the CSAE, 35, 15, pp. 25-32, (2019)
  • [9] DUGA A T, RUYSEN K, DEKEYSER D, Et al., Spray deposition profiles in pome fruit trees: effects of sprayer design, training system and tree canopy characteristics, Crop Protection, 67, pp. 200-213, (2015)
  • [10] DUGA A T, DEKEYSER D, RUYSEN K, Et al., Numerical analysis of the effects of wind and sprayer type on spray distribution in different orchard training systems, Boundary-Layer Meteorology, 157, 3, pp. 517-535, (2015)
123