Influence of circular hole defect on dynamic crack propagation behavior under impact loads

被引：0

作者：

Wang L. ^{[1
]}

Zhu Z. ^{[1
]}

Zhou L. ^{[1
,2
]}

Dong Y. ^{[1
]}

Niu C. ^{[1
]}

Yang Z. ^{[1
]}

机构：

[1] MOE Key Laboratory of Deep Earth Science and Engineering, College of Architecture and Environment, Sichuan University, Chengdu

[2] State Key Laboratory of Geohazard Prevention and Geoenvironment Protection, Chengdu University of Technology, Chengdu

来源：

Baozha Yu Chongji/Explosion and Shock Waves | 2021年 / 41卷 / 08期

关键词：

Crack propagation behavior; Dynamic fracture toughness; Dynamic loads; Hole defect;

D O I：

10.11883/bzycj-2021-0062

中图分类号：

学科分类号：

摘要：

Cavities and crack defects usually coexist in deep earth rock mass structures, which together affect the structural safety and stability of rock masses. In order to study the effect of circular cavity on crack propagation behavior in rock mass under dynamic loads, circular opening specimens with straight crack cavity (COSSCC) specimen were proposed in this study, and a large-scale drop hammer impact device was applied to conduct impact tests. Crack propagation gauges were implemented to measure fracture mechanics parameters, such as dynamic crack initiation time and crack propagation velocity. Then a modified finite difference code Autodyn was applied to carry out the numerical simulation analysis of crack propagation path and stress field around the circular hole. The traditional finite element code Abaqus was also used to calculate the dynamic initiation toughness and dynamic propagation toughness. The results indicate that: (1) when the inclination θ of the circle hole is less than 10°, the crack propagation path deflects and passes through the surface of the circle hole; when the inclination θ of circle hole is 20° and 30°, the crack propagation paths deflects in the direction of the hole but does not pass through the circular hole, indicating that the circular hole has obvious guiding effect on crack propagation; when the inclination θ of circle hole is 40° and 50°, crack propagation path does not deflect, and the guiding effect of the circular hole is obvious weaken. (2) When the crack propagation path reaches the vicinity of the circular hole, the tensile stress zone at the crack tip coincides with the tensile stress zone at the edge of the circular hole. At this time, the crack propagation speed increases significantly, and the dynamic fracture toughness of the crack decreases significantly. (3) The deflection direction of the crack is basically the same as the direction of the maximum circumferential stress at the crack tip. (4) The dynamic fracture toughness of the crack is always smaller than the crack initiation toughness, and the dynamic fracture toughness of the crack has a linear relationship with the dynamic crack growth rate. The larger the dynamic crack growth rate, the smaller the dynamic fracture toughness of the crack. © 2021, Editorial Staff of EXPLOSION AND SHOCK WAVES. All right reserved.

引用

共 34 条

[1] WU Q H, WENG L, ZHAO Y, Et al., On the tensile mechanical characteristics of fine-grained granite after heating/cooling treatments with different cooling rates, Engineering Geology, 253, pp. 94-110, (2019)
[2] SHE S G, LIN P., Several progress and challenges of Chinese rock engineering, Chinese Journal of Rock Mechanics and Engineering, 33, 3, pp. 433-457, (2014)
[3] YU L Y, SU H J, JING H W, Et al., Experimental study of the mechanical behavior of sandstone affected by blasting, International Journal of Rock Mechanics & Mining Sciences, 93, pp. 234-241, (2017)
[4] FAN X, CHEN R, LIN H, Et al., Cracking and failure in rock specimen containing combined flaw and hole under uniaxial compression, Advances in Civil Engineering, pp. 1-15, (2018)
[5] GONG S X, MEGUID S A., A general solution to the antiplane problem of an arbitrarily located elliptical hole near the tip of a main crack, International Journal of Fracture, 28, 2, pp. 249-263, (1991)
[6] MEGUID S A, WANG X D., The dynamic interaction of a crack with a circular hole under antiplane loading, Journal of the Mechanics and Physics of Solids, 43, 22, pp. 1857-1871, (1995)
[7] YANG R S, ZUO J J, FANG S Z, Et al., Experimental study on the effect of circular hole defect on the growth behavior of explosive crack, Vibration and Impact, 37, 12, pp. 174-178, (2018)
[8] LI M, ZHU Z M, LIU R F, Et al., Effect of void on dynamic propagation behavior of explosive crack, Journal of Geotechnical Engineering, 40, 12, pp. 2191-2199, (2018)
[9] WANG Q Z, FENG F, NI M, Et al., Measurement of mode Ⅰ and mode Ⅱ rock dynamic fracture toughness with cracked straight through flattened Brazilian disc impacted by split Hopkinson pressure bar, Engineering Fracture Mechanics, 78, 12, pp. 2455-2469, (2011)
[10] WANG M, ZHU Z M, DONG Y Q, Et al., Study of mixed-mode Ⅰ/Ⅱ fractures using single cleavage semicircle specimens under impacting loads [J], Engineering Fracture Mechanics, 177, pp. 33-44, (2017)

← 1 2 3 4 →