Correction method for edge deviation of line laser sensor

被引：0
|
作者：
Zhao H. [1 ]
Jiang W. [1 ]
Yang L. [1 ]
Luo Z. [1 ]
Li H. [2 ]
机构：
[1] College of Metrology and Measurement Engineering, China Jiliang University, Hangzhou
[2] Science and Technology on Space Physics Laboratory, China Academy of Launch Vehicle Technology, Beijing
来源：
Hongwai yu Jiguang Gongcheng/Infrared and Laser Engineering | 2022年 / 51卷 / 04期
关键词：
Algorithm; Error compensation; Line laser; Point cloud; Profile measurement;
D O I：
10.3788/IRLA20210317
中图分类号：
学科分类号：
摘要：
In order to correct the edge deviation of the line laser sensor in profile measurement, an edge deviation correction method was proposed. This method established a hybrid denoising model based on Manhattan distance and Chebyshev distance by analyzing the main error sources of edge deviation, and have achieved the filtering of spurious noise. In addition, the error model of line laser profile measurement was compensated by the least square. In order to verify the effectiveness of this method, the nominal size of the gauge block was used as an evaluation index to carry out measurement and calibration experiments. The experimental results show that the correction method has a significant effect on filtering stray noise. Among them, the uncompensated size measurement error is 0.43 mm, and the size measurement error is compensated is as small as 0.04 mm after the correction method, which is an order of magnitude lower than the former. Therefore, this method can effectively correct the edge deviation and improve the profile measurement accuracy of the line laser sensor. Copyright ©2022 Infrared and Laser Engineering. All rights reserved.
引用
收藏
相关论文
共 13 条
  • [1] Ma G Q, Liu L, Yu Z L, Et al., Application and development of three-dimensional profile measurement for large and complex surface, Chinese Optics, 12, 2, pp. 214-228, (2019)
  • [2] Zhou Z, Liu W, Wu Q, Et al., A combined measurement method for large-size aerospace components, Sensors, 20, 17, (2020)
  • [3] Zhang T, Li B, Zou Y B., Scanning imaging system based on stripe type laser sensor and robot, Infrared and Laser Engineering, 44, 1, pp. 53-58, (2015)
  • [4] Wang Y H, Zhang Q, Hu Y, Et al., 3D small-field surface imaging based on microscopic fringe projection profilometry: a review, Chinese Optics, 14, 3, pp. 447-457, (2021)
  • [5] Song X F, Li J P, Chen H J, Et al., Laser centerline extraction method for 3D measurement of structured light in multi-scenarios, Infrared and Laser Engineering, 49, 1, (2020)
  • [6] Wu X J, Tang N, Liu B, Et al., A novel high precise laser 3D profile scanning method with flexible calibration, Optics and Lasers in Engineering, 132, (2020)
  • [7] Pan H H, Wang Y W, Xu D B, Et al., Calibration of line-structure light plane using non-specific target, Optics and Precision Engineering, 29, 1, pp. 54-60, (2021)
  • [8] Tang J, Tan X, Li X, Et al., Research on edge detection algorithm based on line laser scanning, Procedia CIRP, 84, pp. 1101-1106, (2019)
  • [9] Wang C J, Shi N N, Sun T, Et al., Image deblurring for laser active illumination based on light vein features, Optics and Precision Engineering, 24, 5, pp. 1159-1167, (2016)
  • [10] Zhang H X, Wang Q, Zhang T F, Et al., Detection algorithm of image edge for laser active imaging, Laser & Infrared, 46, 6, pp. 755-760, (2016)
12