Structural Design of a 7-DOF Manipulator and Its Geometric Position Error Analysis

被引：0
|
作者：
Gao Y. [1 ]
Fang L.-J. [2 ]
Xu J.-Q. [2 ]
Gong Y.-P. [1 ]
机构：
[1] School of Mechanical Engineering and Automation, Northeastern University, Shenyang
[2] School of Robot Science and Engineering, Northeastern University, Shenyang
来源：
Dongbei Daxue Xuebao/Journal of Northeastern University | 2022年 / 43卷 / 07期
关键词：
7-DOF manipulator; error analysis; error model; sensitivity analysis; structural design;
D O I：
10.12068/j.issn.1005-3026.2022.07.013
中图分类号：
学科分类号：
摘要：
A 7-DOF cooperative manipulator was designed and manufactured based on the joint driven by dual motor servo. The geometric error model of the end-effector of the manipulator was established， and the parameter errors were analyzed and synthesized based on the principle of independent action of the original parameter errors. Based on the law of large numbers of mathematical statistics and Monte Carlo method， the sensitivity of influencing factors of the geometric position errors was analyzed by numerical simulation， and the parameter errors which have relatively greater influence on the geometric position errors of the manipulator were found. Through the calculation and analysis of the geometric position errors of the end-effector of the manipulator， it was found that the errors obey the Rayleigh distribution in the workspace of the manipulator. The experimental measurement showed that the repeated positioning error of the manipulator is less than 0.0591mm， and the absolute positioning error obeys Rayleigh distribution significantly. It proved that the double motor servo-driven joint has the characteristics of small return errors and high transmission accuracy， and the error analysis is correct， which provides a theoretical basis for the precision design and application of the manipulator. © 2022 Northeastern University. All rights reserved.
引用
收藏
页码：1003 / 1009+1018
相关论文
共 14 条
  • [1] Yue-pin Lu, Han-yang Zhang, Breaking the seven axis industrial robot development [J], Robotics Industry, 2, pp. 35-41, (2016)
  • [2] Wu C H., A kinematic CAD tool for the design and control of a robot manipulator [J], The International Journal of Robotics Research, 3, 1, pp. 58-67, (1984)
  • [3] Veitschegger W K, Wu C H., Robot accuracy analysis based on kinematics [J], IEEE Journal on Robotics and Automation, 2, 3, pp. 171-179, (1986)
  • [4] Shiakolas P S, Conrad K L, Yih T C., On the accuracy，repeatability，and degree of influence of kinematics parameters for industrial robots [J], International Journal of Modelling & Simulation, 22, 4, pp. 245-254, (2002)
  • [5] Chen G, Liang Y, Sun Y，, Et al., Volumetric error modeling and sensitivity analysis for designing a five-axis ultra-precision machine tool [J], International Journal of Advanced Manufacturing Technology, 68, pp. 2525-2534, (2013)
  • [6] Si-wei Li, Tian Huang, Attitude precision synthesis and assembly process design of a 3-DOF parallel mechanism with parallelogram branch chain [J], Chinese Journal of Mechanical Engineering, 39, 7, pp. 38-42, (2003)
  • [7] Hui Zheng, Guo-bao Tang, Geometric error modeling and sensitivity analysis of delta parallel manipulator [J], Journal of Harbin Institute of Technology, 41, 7, pp. 252-255, (2009)
  • [8] Lee S C, Zeng Q, Ehmann K F., Error modeling for sensitivity analysis and calibration of the tri-pyramid parallel robot [ J], The International Journal of Advanced Manufacturing Technology, 93, 5, pp. 1319-1332, (2017)
  • [9] Ni Y, Shao C, Zhang B, Et al., Error modeling and tolerance design of a parallel manipulator with full-circle rotation [ J], Advances in Mechanical Engineering, 8, 5, pp. 1-16, (2016)
  • [10] Li-jin Fang, Sun Long-fei, Research on clearance characteristics of dual motor drive system [ J ], China Mechanical Engineering, 23, 24, pp. 2991-2996, (2012)
12