Preparation and performance of graphene/conductive carbon black compounded rubber material for bearings

被引：0
|
作者：
Wu Y. [1 ]
Zhang X. [1 ]
Wang H. [1 ]
Li A. [1 ]
Zhang R. [1 ]
Zhang H. [1 ]
Liu Y. [1 ]
机构：
[1] (School of Civil and Transportation Engineering,Beijing University of Civil Engineering and Architecture,Beijing 102600,China) (School of Civil Engineering,Southeast University,Nanjing 211189,China) (Hengshui Zhentai Vibration Isolation Equipment Co.,Ltd.
来源：
Dongnan Daxue Xuebao (Ziran Kexue Ban)/Journal of Southeast University (Natural Science Edition) | 2024年 / 54卷 / 01期
关键词：
bearings; bromobutyl rubber; conductive carbon black; conductive rubber; graphene;
D O I：
10.3969/j.issn.1001-0505.2024.01.006
中图分类号：
学科分类号：
摘要：
The conductive rubber materials with better damping performance were prepared by using graphene / conductive carbon black (CCB)as functional fillers and brominated butyl rubber (BIIR)as base rubber. The mechanical properties,dynamic mechanical properties (DMA)and resistivity test experiments of 10 formulations with different graphene / CCB components were performed to investigate the influence law of adding graphene and CCB on the performance of BIIR. The results show that CCB has a reinforcing effect on the BIIR material,and the synergistic use of graphene / CCB can effectively improve the damping and conductive properties of BIIR. The tensile and tear strength of BIIR / CCB composites reach 20. 28 MPa and 45. 66 kN / m when 40 g CCB is added to every 100 g total rubber. The maximum loss tangent of the BIIR / CCB / graphene composite rubber material is increased to 0. 5 with a resistivity of 3 646 Ω·cm when the mass ratio of CCB to grapheme composition is 40∶ 10. The optimal ratio of CCB to graphene components for the composites is 40∶ 5. The prepared new composite material has good mechanical properties,damping properties and electrical conductivity. The results can provide a reference for the preparation of high damping conductive rubber bearings. © 2024 Southeast University. All rights reserved.
引用
收藏
页码：44 / 49
页数：5
相关论文
共 20 条
  • [1] Li A Q., Vibration control for building structures:Theory and application [M], (2021)
  • [2] Sheibani M, Ou G., The development of Gaussian process regression for effective regional post-earthquake building damage inference[J], Computer-Aided Civil and Infrastructure Engineering, 36, 3, pp. 264-288, (2021)
  • [3] Shen H J, Wang H, Zheng W Z, Et al., Analysis of critical directions of earthquake input of high-speed railway continuous girder bridges based on fragility analysis method[J], Journal of Southeast University (Natural Science Edition), 49, 5, (2019)
  • [4] Makris N., Seismic isolation:Early history[J], Earthquake Engineering and Structural Dynamics, 48, 2, pp. 269-283, (2019)
  • [5] Zheng W Z, Wang H, Du Y F, Et al., Temperature effect of time-varying modal frequency of base-isolated structure under ambient excitation [J], Journal of Southeast University (Natural Science Edition), 47, 5, (2017)
  • [6] Xiang X W, Wang H, Li A Q, Et al., Aseismic control of continuous bridge with laminated rubber bearings considering ratio of PGA to PGV [J], Journal of Southeast University (Natural Science Edition), 47, 5, pp. 1006-1012, (2017)
  • [7] Wu P S, Wang J, Ou J P., Research and design of main failure modes of seismically isolated structures subjected to very-rare earthquakes[J], Journal of Disaster Prevention and Mitigation Engineering, 40, 3, pp. 317-325, (2020)
  • [8] Zeng Y, Pan P, Cao Y R, Et al., Shear deformation detection in smart rubber bearing (SRB)using active sensing method, Engineering Structures, 242, (2021)
  • [9] Xiang C P, Wang Z J, Yang C H, Et al., Stretchable and fatigue-resistant materials [J], Materials Today, 34, (2020)
  • [10] Wei W, Tan P, Yuan Y, Et al., Experimental and analytical investigation of the influence of compressive load on rate-dependent high-damping rubber bearings, Construction and Building Materials, 200, (2019)
12