Finite element analysis for bolt axial stress measurement based on acoustoelastic effect

被引：0
|
作者：
Sun C. [1 ]
Wang Z. [1 ]
Li J. [1 ]
Sun K. [1 ]
机构：
[1] Institute of Machinery Manufacturing Technology, China Academy of Engineering Physics, Mianyang
来源：
Zhendong yu Chongji/Journal of Vibration and Shock | 2019年 / 38卷 / 13期
关键词：
Acoustoelastic effect; Axial stress; Finite element method; Hyper-elastic material; Ultrasonic measurement;
D O I：
10.13465/j.cnki.jvs.2019.13.023
中图分类号：
学科分类号：
摘要：
To promote the effective application of ultrasonic wave technique in quantitative evaluation of bolt tightening state, combining with requirements of actual detection, an appropriate finite element (FE) model was established for the bolt axial stress measurement method based on acoustoelastic effect. A 2-D axisymmetric mode was used to simulate bolt M8×25, and a 10 MHz ultrasonic transducer was placed on the bolt head. In FE simulation, a hyper-elastic material with Murnaghan third-order elastic constants was used to do coupling analysis for structural field and acoustic one. Through two studying steps, the ultrasonic waveform signal for bolt axial tension state was determined. The FE computation results showed that there is a linear relationship between time difference of ultrasonic wave propagation (ns) and bolt axial stress (MPa), and this relationship varies with change of bolt clamped length and its material; for the bolt axial stress measurement method based on acoustoelastic effect, the linear coefficient's correct measurement is very important. The FE computation results were analyzed deeply, it was shown that bolt stress state has a superposition effect on ultrasonic wave propagation change in bolt; different bolt clamped length causes larger change of acoustoelastic effect, this should be paid enough attentions to; the FE computation results agree well with those of analytical calculation and practical test measurement; the proposed FE model for bolt axial stress measurement with the ultrasonic wave method can be used to solve the difficult problem of acoustoelastic effect's numerical simulation and analysis, and provide a technical guidance for analysis of detection methods and development of specific instruments. © 2019, Editorial Office of Journal of Vibration and Shock. All right reserved.
引用
收藏
页码：164 / 171
页数：7
相关论文
共 14 条
  • [1] Couchman J.C., The acousto-elastic fastener preload indicator, AFML-TR-78-138, (1978)
  • [2] Viktor H., Structural and Residual Stress Analysis by Nondestructive Methods, (1997)
  • [3] Fukuoka H., Development of acoustoelasticity in Japan, Nondestructive Testing and Evaluation, 7, pp. 181-192, (1992)
  • [4] Hughes D.S., Kelly J.L., Second-order elastic deformation of solids, Physical Review, 92, 5, pp. 1145-1149, (1953)
  • [5] Heyman J.S., A CW ultrasonic bolt-strain monitor, Experimental Mechanics, 17, 5, pp. 183-187, (1977)
  • [6] Chaki S., Bourse G., Guided ultrasonic waves for non-destructive monitoring of the stress levels in prestressed steel strands, Ultrasonics, 49, pp. 162-171, (2009)
  • [7] Xu D., Wu X.J., Wang Y.G., Bolt axial stress measurement based on a mode-converted ultrasound method using an electromagnetic acoustic transducer, Ultrasonics, 54, pp. 914-920, (2014)
  • [8] Kamyshev A.V., Nikitina N.E., Smirnov V.A., Et al., Measurement of the residual stresses in the treads of railway wheels by the acoustoelasticity method, Russian Journal of Nondestructive Testing, 46, 3, pp. 189-193, (2010)
  • [9] Montoya A., Doyle D., Maji A., Et al., Ultrasonic evaluation of bolted connections in satellites, Research in Nondestructive Evaluation, 25, pp. 44-62, (2014)
  • [10] Nassar S.A., Veeram A.B., Ultrasonic control of fastener tightening using varying wave speed, Journal of Pressure Vessel Technology, 128, pp. 427-432, (2006)
12