Effect of cooling rate on the peritectic transformation of δ-TRIP steel

被引：0
|
作者：
Jiang L. [1 ]
Liao M.-Y. [1 ]
Wang Z.-D. [1 ]
Zhu H.-X. [1 ]
Cui H. [1 ,2 ]
机构：
[1] Collaborative Innovation Center of Steel Technology, University of Science and Technology Beijing, Beijing
[2] Beijing Laboratory of Metallic Materials and Processing for Modern Transportation, Beijing
来源：
Gongcheng Kexue Xuebao/Chinese Journal of Engineering | 2023年 / 45卷 / 05期
关键词：
cooling rate; differential scanning calorimetry; microsegregation; phase transformation; δ-TRIP steel;
D O I：
10.13374/j.issn2095-9389.2022.03.07.004
中图分类号：
学科分类号：
摘要：
The phase transformation of carbon steel has always been a research hotspot. Researchers study the phase transformation process of steel in terms of the original structure, chemical composition, and process conditions, and the cooling rate in process conditions has an important influence on the phase transformation of steel. In this study, Thermo-calc thermodynamic software is used to simulate and calculate the phase transformation process of 3.52%Al (mass fraction) delta ferrite transformation-induced plasticity (δ-TRIP) steel, and differential scanning calorimetry (DSC) and the Ohnaka microsegregation model are used to analyze the effect of cooling rate on the peritectic transformation temperature and solute element segregation during solidification of 3.52%Al δ-TRIP steel. The results show that the smaller the cooling rate is, the closer the DSC phase transition temperature is to the thermodynamic equilibrium value calculated by Thermo-calc. Increasing the cooling rate from 10 to 30 to 50 ℃·min−1 decreases the phase transition temperature of L→L+δ and first decreases and then increases those of L+δ→L+δ+γ and L+δ+γ→δ+γ. The former temperature is mainly affected by cooling, and the latter temperatures are mainly affected by element segregation. Among the six elements (C, Si, Mn, P, S, and Al) of 3.52%Al δ-TRIP steel, the segregation of S is the most severe. This result is obtained because the partition coefficient k of the S element at the solid –liquid interface is much smaller than those of other solute elements. The rapid S element enrichment at the end of solidification increases the possibility of sulfide precipitation, forms a low melting point liquid film between dendrites, reduces the zero plastic temperature, and increases the solidification brittleness range and crack sensitivity. Therefore, the sulfur content in steel should be strictly controlled during composition smelting. The cooling rate slightly affects C, Mn, and S segregation but greatly affects Si, P, and Al segregation, and the degree of segregation of Si, P, and Al increases with the cooling rate. The segregation of Si, P, and Al delays the peritectic reaction process, the segregation of Si and P slightly delays the peritectic reaction process, and Al segregation clearly delays the peritectic reaction process. With increasing cooling rate, the lower the peritectic reaction area moves, the slower the peritectic reaction process. This study can provide a theoretical basis for the continuous casting process parameters of δ-TRIP steel. © 2023 Science Press. All rights reserved.
引用
下载
收藏
页码：747 / 754
页数：7
相关论文
共 23 条
  • [1] Ma M T, Yi H L, Lu H Z, Et al., On the lightweighting of automobile, Eng Sci, 11, 9, (2009)
  • [2] Yang Q, Wang J F, Cong Y, Et al., State of knowledge on lightweight steels(Part Ⅰ) —Al-rich interstitial-free steels and ferritic lightweight steels, Baosteel Technol, 3, (2015)
  • [3] Yi H L, Chen P, Wang G D, Et al., δ-TRIP steel: Physical and mechanical metallurgy, Eng Sci, 16, 2, (2014)
  • [4] Chatterjee S, Murugananth M, Bhadeshia H K D H., δTRIP steel, Mater Sci Technol, 23, 7, (2007)
  • [5] Xie L, Huang T L, Wang Y H, Et al., Deformation induced martensitic transformation and its initial microstructure dependence in a high alloyed duplex stainless steel, Steel Res Int, 88, 12, (2017)
  • [6] Jamei F, Mirzadeh H, Zamani M., Synergistic effects of holding time at intercritical annealing temperature and initial microstructure on the mechanical properties of dual phase steel, Mater Sci Eng A, 750, (2019)
  • [7] Liang J T, Zhao Z Z, Liu K, Et al., Microstructure and properties of 1300-MPa grade Nb microalloying DH steel, Chin J Eng, 43, 3, (2021)
  • [8] Zhang Y G, Zhao A M, Zhao Z Z, Et al., Influence of alloying element on continuous cooling solid phase transformation and hardness of TRIP steels, J Shenyang Univ Technol, 32, 4, (2010)
  • [9] Bocharova E, Khlopkov K, Sebald R., Effect of microalloying elements on phase transformation, microstructure and mechanical properties in dual-phase steels, Mater Sci Forum, 879, (2016)
  • [10] Chen Y L, Dong C, Jiang H T, Et al., Effect of aluminum and silicon on phase transformation and microstructure of quenching and partitioning steel during continuous cooling, Hot Work Technol, 39, 2, (2010)
123