Production of Potassium Isotope Radioactive Ion Beam at BRISOL Facility

被引：0

作者：

Ma X. ^{[1
]}

Cui B. ^{[1
]}

Tang B. ^{[1
]}

Ma R. ^{[1
]}

Chen L. ^{[1
]}

Ma Y. ^{[1
]}

Wang Y. ^{[1
]}

Huang Q. ^{[1
]}

Zhang Y. ^{[1
]}

Yu R. ^{[1
]}

机构：

[1] Department of Nuclear Physics, China Institute of Atomic Energy, Beijing

来源：

Yuanzineng Kexue Jishu/Atomic Energy Science and Technology | 2022年 / 56卷 / 10期

关键词：

CaO target; isotope separator on-line; radioactive ion beam;

D O I：

10.7538/yzk.2021.youxian.0941

中图分类号：

学科分类号：

摘要：

The Beijing radioactive ion beam facility isotope separator on-line (BRISOL) is a radioactive ion beam facility based on a 100 MeV@200 μA proton cyclotron. The radioactive ion beams are produced by bombarding the thick target with proton beam provided by cyclotron. The mass resolving power of the BRISOL is better than 20 000. The first radioactive beams of 37K+ and 38K+ were generated at BRISOL with CaO targets in 2015, and the maximum current of the 38K+ beam is only 1×106 pps when the current of proton beam is 0.5 μA. The collinear laser spectroscopy experiments using 37-43K+ beams will be carried out on BRISOL. The yields of 37-43K+ would not be less than 1×106 pps in the experiment. In order to fulfill the requirements, it is necessary to increase the yield of radioactive ion beams. So a series of studies were carried out. The first step is the targets preparation. According to the requirements of the ISOL targets, CaO was selected as the targets material for the generation of radioactive ion beams. The CaO targets were prepared by cold pressing methods with Ca (OH)2, carboxymethyl cellulose (CMC) and deionized water. CMC was added as a binder and pore -forming agent. Those materials were mixed in proportion and were cold pressed into desired shape. The thermal treatment was performed in a graphite furnace. After sintering, the targets were porous and then loaded into the targets container. The ion source with the ability of dual ionization mode, including surface ionization mode and FEBIAD ionization mode, was applied in the study. In order to improve the surface ionization efficiency for K, a 0.1 mm thick rhenium metal lining was installed on the inner wall of the cathode. Then an offline experiment was conducted and the spectra of CaO targets were measured. The experimental results show that Ca+ is ionized when the cathode current is high enough. Therefore, it is necessary to optimize the cathode currents for larger yield of K+. After that, an online experiment at BRISOL was carried out. The experiment results show that the 36-38,43,45-47K beams are produced successfully. The yield of 38K+ is increased to 1.12×1010 pps when the proton beam is 10 μA, the much larger yields are achieved through increasing proton intensities, optimizing both the structure of ion source and the targets working temperature. The development of CaO targets and the results of on-line experiment will be presented in this paper. © 2022 Atomic Energy Press. All rights reserved.

引用

下载

页码：2172 / 2177

页数：5

共 12 条

[1] TANG B, CUI B, CHEN L, Et al., The commissioning of the BRISOL facility, Nucl Instrum Methods B, 376, pp. 429-433, (2016)
[2] CUI Baoqun, TANG Bing, MA Yingjun, Et al., Development of Beijing radioactive ion beam facility isotope separator on-line, Atomic Energy Science and Technology, 53, 9, pp. 1572-1576, (2019)
[3] (2002)
[4] KONING A J, ROCHMAN D, SUBLET J, Et al., TENDL: Complete nuclear data library for innovative nuclear science and technology, Nuclear Data Sheets, (2019)
[5] LI Yangjuan, CHENG Zhiqiang, ZHANG Huanqi, Et al., A novel technique for preparation of the porous adsorbent NaF and a preliminary study on its adsorption capacity for MoF<sub>6</sub>, Nuclear Techniques, 37, 8, (2014)
[6] ALYAKRINSKIY O, GUBIN K, MARTYSHKIN P, Et al., Influence of grain size and porosity on the release of radioactive isotopes from target materials with high open porosity, Nucl Instrum Methods B, 267, pp. 2554-2558, (2009)
[7] BIASETTO L, CARTURAN S, MAGGIONI G, Et al., Fabrication of mesoporous and high specific surface area lanthanum carbide-carbon nanotube composites, Journal of Nuclear Materials, 385, pp. 582-590, (2009)
[8] TANG Bing, CUI Baoqun, MA Xie, Et al., Production of sodium isotope radioactive ion beam on BRISOL facility, Atomic Energy Science and Technology, 54, 5, pp. 882-887, (2020)
[9] TANG Bing, CUI Baoquan, CHEN Lihua, Et al., The development of the FEBIAD ion source for BRISOL, Nucl Instrum Methods in Physics Research B, 463, pp. 154-157, (2020)
[10] MA Yingjun, CUI Baoqun, YAN Mingfang, Et al., Beam identification unit in BRISOL, Nuclear Physics Review, 32, pp. 1-4, (2015)

← 1 2 →