Preparation and Characterization of Stainless Steel/TiC Nanocomposite Particles by Ball-milling Method

被引：0
|
作者：
陈文怡
机构：
[1] StateKeyLabofAdvancedTechnologyforMaterialsSynthesisandProcessing,WuhanUniversityofTechnology
来源：
JournalofWuhanUniversityofTechnology(MaterialsScienceEdition) | 2009年 / 24卷 / 01期
关键词：
D O I：
暂无
中图分类号：
学科分类号：
摘要：
A stainless steel/10wt%TiC nanocomposite particles were prepared by high-energy ball-milling method using stainless steel, carbon and titanium as raw materials. The evolution of phase composition, microstructure and specific surface area of the stainless steel/TiC nanocomposite particles with increasing ball-milling time in the range of 0-100 h were investigated by XRD, SEM, TEM and BET techniques. The results showed that the stainless steel/TiC nano-composite particles were fabricated when the ball-milling time was longer than 20 h. However, the nanocomposite particles were soldered and agglomerated again when the ball-milling time was longer than 60 h. The microstructure of the composite particles transformed from lamellar structure to nanostructure during the repeated process of the cold welding and cracking. TEM image reveals clearly that the in-situ TiC nanoparticles with grain size of 3-8 nm are in the interior of the stainless steel/TiC nanocomposite particles obtained by ball-milling 100 h.
引用
收藏
页数：4
相关论文
共 50 条
  • [1] Preparation and characterization of stainless steel/TiC nanocomposite particles by ball-milling method
    Chen Wenyi
    Zhou Jian
    [J]. JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION, 2009, 24 (01): : 38 - 41
  • [2] Preparation and Characterization of Stainless Steel/TiC Nanocomposite Particles by Ball-milling Method
    陈文怡
    [J]. Journal of Wuhan University of Technology(Materials Science), 2009, 24 (01) : 38 - 41
  • [3] Preparation and characterization of stainless steel/TiC nanocomposite particles by ball-milling method
    Wenyi Chen
    Jian Zhou
    [J]. Journal of Wuhan University of Technology-Mater. Sci. Ed, 2009, 24 : 38 - 41
  • [4] Structural characterization of stainless steel/TiC nanocomposites produced by high-energy ball-milling method at different milling times
    Sheikhzadeh, M.
    Sanjabi, S.
    [J]. MATERIALS & DESIGN, 2012, 39 : 366 - 372
  • [5] Raman spectroscopy fingerprint of stainless steel-MWCNTs nanocomposite processed by ball-milling
    Leite dos Reis, Marcos Allan
    Barbosa Neto, Newton Martins
    Santos de Sousa, Mario Edson
    Araujo, Paulo T.
    Simoes, Sonia
    Vieira, Manuel F.
    Viana, Filomena
    Loayza, Cristhian R. L.
    Borges, Diego J. A.
    Cardoso, Danyella C. S.
    Assuncao, Paulo D. C.
    Braga, Eduardo M.
    [J]. AIP ADVANCES, 2018, 8 (01)
  • [6] Preparation of fine AlN powders by wet ball-milling and their characterization
    Toyo Aluminium K.K., Osaka, Japan
    [J]. J Ceram Soc Jpn, 1217 (6-10):
  • [7] Preparation of fine AlN powders by wet ball-milling and their characterization
    Nagai, Y
    Lai, GC
    [J]. JOURNAL OF THE CERAMIC SOCIETY OF JAPAN, 1997, 105 (01) : 6 - 10
  • [8] Study on the oxidation resistance of 316 stainless steel nano-powder prepared by ball-milling method
    Chen Wenyi
    Zhou Jian
    Liu Ying
    [J]. ADVANCED SYNTHESIS AND PROCESSING TECHNOLOGY FOR MATERIALS, 2009, 66 : 151 - 154
  • [9] Preparation of Ti3SiC2/Al nanocomposite by using mechanical ball-milling method
    School of Mechanical Engineering, Shandong University of Technology, Zibo 255049, China
    [J]. Fuhe Cailiao Xuebao, 2006, 6 (134-137):
  • [10] Dry ball-milling preparation and characterization of graphite-phthalocyanine composites
    Basiuk, Vladimir A.
    Mendoza-Dominguez, Carlos U.
    Meza-Laguna, Victor
    Molina-Sevilla, Paola
    Alvarez-Zauco, Edgar
    Serrano, Manuel
    Vlasova, Marina
    Basiuk, Elena V.
    [J]. FULLERENES NANOTUBES AND CARBON NANOSTRUCTURES, 2023, 31 (09) : 815 - 827
12345