A STUDY OF FATIGUE CRACK-GROWTH IN A PARTICULATE-REINFORCED AL-SI ALLOY AT 23-DEGREES-C AND 220-DEGREES-C

被引：23

作者：

HEALY, JC ^{[1
]}

BEEVERS, CJ ^{[1
]}

机构：

[1] UNIV BIRMINGHAM,SCH MET & MAT,BIRMINGHAM B15 2TT,W MIDLANDS,ENGLAND

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 1991年 / 142卷 / 02期

关键词：

D O I：

10.1016/0921-5093(91)90657-9

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

A study of short- and long-fatigue-crack growth in A356, a cast Al-Si alloy, reinforced with 20% volume fraction of silicon carbide (SiC) particulate, was carried out at 23-degrees-C. Long-crack growth tests were performed at 220-degrees-C. Short-crack growth was observed below the long-crack threshold stress intensity at 23-degrees-C and was dominated by interactions between the crack tips and the SiC particulate. In the long-crack tests at R = 0.1 and R = 0.5 a stress ratio effect on crack growth was observed at 23-degrees-C, which was more marked than that observed at 220-degrees-C. Examination of fatigue fracture surfaces revealed a matrix-dominated mode of crack growth at 220-degrees-C compared with that at 23-degrees-C where the SiC particulate played a significant role in the fatigue fracture process.

引用

页码：183 / 192

页数：10

共 32 条

[1] Effect of SiC particles on fatigue crack growth behavior of SiC particulate-reinforced Al-Si alloy composites produced by spray forming
Li, W.
Liang, H.
Chen, J.
Zhu, S. Q.
Chen, Y. L.
20TH EUROPEAN CONFERENCE ON FRACTURE, 2014, 3 : 1694 - 1699
[2] Influence of porosity on fatigue resistance of cast SiC particulate-reinforced Al-Si alloy composite
Li, CS
Ellyin, F
Koh, S
Oh, SJ
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2000, 276 (1-2): : 218 - 225
[3] THE EFFECT OF MICROSTRUCTURE ON 650-DEGREES-C FATIGUE CRACK-GROWTH IN R M ASTROLOY
GAYDA, J
MINER, RV
JOURNAL OF METALS, 1982, 34 (08): : 71 - 71
[4] THE EFFECT OF MICROSTRUCTURE ON 650-DEGREES-C FATIGUE CRACK-GROWTH IN P/M ASTROLOY
GAYDA, J
MINER, RV
METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1983, 14 (11): : 2301 - 2308
[5] THE MICROMECHANICS OF FATIGUE CRACK-GROWTH AT 25-DEGREES-C IN TI-6AL-4V REINFORCED WITH SCS-6 FIBERS
DAVIDSON, DL
METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1992, 23 (03): : 865 - 879
[6] TENSILE AND FATIGUE PROPERTIES OF A 25-VOL-PERCENT SIC PARTICULATE-REINFORCED 6090-AL COMPOSITE AT 300-DEGREES-C
NIEH, TG
LESUER, DR
SYN, CK
SCRIPTA METALLURGICA ET MATERIALIA, 1995, 32 (05): : 707 - 712
[7] INFLUENCE OF PROLONGED THERMAL EXPOSURE ON INTERGRANULAR FATIGUE CRACK-GROWTH BEHAVIOR IN ALLOY-718 AT 650-DEGREES-C
ZHENG, D
GHONEM, H
METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1992, 23 (11): : 3169 - 3171
[8] FATIGUE AND CREEP CRACK-GROWTH IN METHANE REFORMER TUBES AT TEMPERATURES ABOVE 700-DEGREES-C
RODIG, M
KIENZLER, R
NICKEL, H
SCHUBERT, F
NUCLEAR ENGINEERING AND DESIGN, 1988, 108 (03) : 467 - 476
[9] FATIGUE CRACK-GROWTH CURVE IN AIR ENVIRONMENT AT 300-DEGREES-C FOR STAINLESS-STEELS
BERNARD, JL
SLAMA, GS
NUCLEAR TECHNOLOGY, 1982, 59 (01) : 136 - 147
[10] FATIGUE-CRACK GROWTH THROUGH THE LAMELLAR MICROSTRUCTURE OF AN ALLOY BASED ON TIAL AT 25-DEGREES-C AND 800-DEGREES-C
DAVIDSON, DL
CAMPBELL, JB
METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1993, 24 (07): : 1555 - 1574

← 1 2 3 4 →